<!DOCTYPE html PUBLIC "-//W3C//DTD HTML 4.01 Transitional//EN">
<html>
<head>
<meta content="text/html;charset=ISO-8859-1" http-equiv="Content-Type">
</head>
<body bgcolor="#ffffff" text="#000000">
OK I ran the command and received the following output. I thought I
could see it in real time like clogin unless this is an error. I
noticed that it said clogin not found but I can run that by itself and
its fine.<br>
<br>
<br>
raphael# ./rancid -d 10.0.0.1<br>
executing clogin -t 90 -c"admin show version;show version;show
redundancy secondary;show idprom backplane;show install active;admin
show env all;show env all;show rsp chassis-info;show gsr chassis;show
diag chassis-info;show boot;show bootvar;admin show variables boot;show
variables boot;show flash;dir /all nvram:;dir /all bootflash:;dir /all
slot0:;dir /all disk0:;dir /all slot1:;dir /all disk1:;dir /all
slot2:;dir /all disk2:;dir /all harddisk:;dir /all harddiska:;dir /all
harddiskb:;dir /all sup-bootflash:;dir /all sup-microcode:;dir /all
slavenvram:;dir /all slavebootflash:;dir /all slaveslot0:;dir /all
slavedisk0:;dir /all slaveslot1:;dir /all slavedisk1:;dir /all
slaveslot2:;dir /all slavedisk2:;dir /all slavesup-bootflash:;dir /all
sec-nvram:;dir /all sec-bootflash:;dir /all sec-slot0:;dir /all
sec-disk0:;dir /all sec-slot1:;dir /all sec-disk1:;dir /all
sec-slot2:;dir /all sec-disk2:;show controllers;show controllers
cbus;show diagbus;admin show diag;show diag;show module;show spe
version;show c7200;show inventory raw;show vtp status;show vlan;show
vlan-switch;show debug;show running-config;write term" 10.0.0.1<br>
clogin: not found<br>
10.0.0.1: missed cmd(s): admin show diag,dir /all slavedisk2:,show rsp
chassis-info,dir /all sec-slot2:,show diag,dir /all disk1:,show gsr
chassis,dir /all sec-nvram:,show diag chassis-info,dir /all disk2:,dir
/all sec-bootflash:,show spe version,dir /all slaveslot2:,dir /all
disk0:,show install active,show bootvar,dir /all slaveslot0:,dir /all
sec-slot1:,dir /all harddiska:,dir /all slavenvram:,show flash,dir /all
sec-disk2:,dir /all slavesup-bootflash:,dir /all sec-disk0:,dir /all
harddiskb:,show variables boot,show boot,show inventory raw,dir /all
slavedisk1:,show env all,show module,admin show env all,show
controllers,admin show version,show diagbus,dir /all slavedisk0:,show
debug,show idprom backplane,dir /all bootflash:,dir /all sec-slot0:,dir
/all sec-disk1:,write term,show vtp status,dir /all sup-bootflash:,dir
/all slot2:,dir /all harddisk:,dir /all slot0:,dir /all
sup-microcode:,show vlan,dir /all slavebootflash:,show controllers
cbus,dir /all slaveslot1:,dir /all nvram:,show version,show
vlan-switch,admin show variables boot,show redundancy secondary,show
running-config,show c7200,dir /all slot1:<br>
10.0.0.1: missed cmd(s): admin show diag,dir /all slavedisk2:,show rsp
chassis-info,dir /all sec-slot2:,show diag,dir /all disk1:,show gsr
chassis,dir /all sec-nvram:,show diag chassis-info,dir /all disk2:,dir
/all sec-bootflash:,show spe version,dir /all slaveslot2:,dir /all
disk0:,show install active,show bootvar,dir /all slaveslot0:,dir /all
sec-slot1:,dir /all harddiska:,dir /all slavenvram:,show flash,dir /all
sec-disk2:,dir /all slavesup-bootflash:,dir /all sec-disk0:,dir /all
harddiskb:,show variables boot,show boot,show inventory raw,dir /all
slavedisk1:,show env all,show module,admin show env all,show
controllers,admin show version,show diagbus,dir /all slavedisk0:,show
debug,show idprom backplane,dir /all bootflash:,dir /all sec-slot0:,dir
/all sec-disk1:,write term,show vtp status,dir /all sup-bootflash:,dir
/all slot2:,dir /all harddisk:,dir /all slot0:,dir /all
sup-microcode:,show vlan,dir /all slavebootflash:,show controllers
cbus,dir /all slaveslot1:,dir /all nvram:,show version,show
vlan-switch,admin show variables boot,show redundancy secondary,show
running-config,show c7200,dir /all slot1:<br>
10.0.0.1: End of run not found<br>
10.0.0.1: End of run not found<br>
!<br>
raphael# <br>
<br>
<br>
Lance Vermilion wrote:
<blockquote
cite="mid:8423e7bb0811110738r57ecfda8h1b204407817ade1b@mail.gmail.com"
type="cite">
<pre wrap="">Sean,
clogin is purely the login script. You must run "rancid -d <host>" to
see what you are looking for.
-Lance
On Mon, Nov 10, 2008 at 6:11 PM, Sean Murphy <a class="moz-txt-link-rfc2396E" href="mailto:smurphy@calarts.edu"><smurphy@calarts.edu></a> wrote:
</pre>
<blockquote type="cite">
<pre wrap="">I am trying to see the entire RANCID process from beginning to end first
with clogin and having it login run the config portion and finally logout.
I have tried /usr/local/libexec/rancid/clogin 10.0.0.1
This just shows the login portion. Is there a way to see everything?
Thanks.
_______________________________________________
Rancid-discuss mailing list
<a class="moz-txt-link-abbreviated" href="mailto:Rancid-discuss@shrubbery.net">Rancid-discuss@shrubbery.net</a>
<a class="moz-txt-link-freetext" href="http://www.shrubbery.net/mailman/listinfo.cgi/rancid-discuss">http://www.shrubbery.net/mailman/listinfo.cgi/rancid-discuss</a>
</pre>
</blockquote>
<pre wrap=""><!---->_______________________________________________
Rancid-discuss mailing list
<a class="moz-txt-link-abbreviated" href="mailto:Rancid-discuss@shrubbery.net">Rancid-discuss@shrubbery.net</a>
<a class="moz-txt-link-freetext" href="http://www.shrubbery.net/mailman/listinfo.cgi/rancid-discuss">http://www.shrubbery.net/mailman/listinfo.cgi/rancid-discuss</a>
</pre>
</blockquote>
</body>
</html>