Yep, it works on a8. I just downgraded and all is good.<br><br><div class="gmail_quote">On Fri, Jan 30, 2009 at 5:06 PM, Michael Stefaniuc <span dir="ltr"><<a href="mailto:mstefani@redhat.com">mstefani@redhat.com</a>></span> wrote:<br>
<blockquote class="gmail_quote" style="border-left: 1px solid rgb(204, 204, 204); margin: 0pt 0pt 0pt 0.8ex; padding-left: 1ex;"><div class="Ih2E3d">Sreekanth K wrote:<br>
> Me too have the same problem... I am on 2.3.2a9... Can someone help!!!<br>
</div>I'm still on a8 and it works there. It was fixed in a5 or a6 time frame<br>
when the two patches went in. I might upgrade to a9 but I'm pretty busy<br>
at the moment and don't have time for that.<br>
<br>
bye<br>
<font color="#888888"> michael<br>
</font><div class="Ih2E3d"><br>
> On Thu, Jan 29, 2009 at 7:42 PM, Ryan DeBerry <<a href="mailto:rdeberry@gmail.com">rdeberry@gmail.com</a>> wrote:<br>
><br>
>> Yes, I am using cat5 as the device type. I can run clogin and it works<br>
>> fine. rancid-run produces the following log.<br>
>><br>
>> missed cmd(s): write term all,show port ifindex,show module,dir<br>
>> sup-microcode:,dir sup-bootflash:,dir bootflash:,dir slot0:,show<br>
>> version,show flash,show running-config,write term,show boot,dir slot1:,show<br>
>> inventory raw<br>
>> : End of run not found<br>
>><br>
>><br>
>> Below is a link to old thread.<br>
>><br>
>> <a href="http://osdir.com/ml/network.rancid/2008-06/msg00018.html" target="_blank">http://osdir.com/ml/network.rancid/2008-06/msg00018.html</a><br>
>><br>
>><br>
>> On Thu, Jan 29, 2009 at 1:05 PM, Michael Stefaniuc <<a href="mailto:mstefani@redhat.com">mstefani@redhat.com</a>>wrote:<br>
>><br>
>>> Ryan DeBerry wrote:<br>
>>>> I have seen many posts in the archives with the same issue but I have<br>
>>> not<br>
>>>> seen a resolution.<br>
>>> Which rancid version are you using? I have submitted patches to fix the<br>
>>> problem and those were accepted (in a modified) form upstream. I use<br>
>>> rancid-2.3.2a8 and the only CatOS specific patch I have is to kill the<br>
>>> bogus "set portcost" config lines.<br>
>>><br>
>>>> clogin works just fine but rancid-run spits out error timeout reached<br>
>>> Btw. what device type are you using for the CatOS devices: "cisco" or<br>
>>> "cat5"? "cat5" is the correct type.<br>
<br>
<br>
<br>
</div>--<br>
<div><div></div><div class="Wj3C7c">Michael Stefaniuc Tel.: +49-711-96437-199<br>
Consulting Communications Engineer Fax.: +49-711-96437-111<br>
--------------------------------------------------------------------<br>
Reg. Adresse: Red Hat GmbH, Otto-Hahn-Strasse 20, 85609 Dornach bei Muenchen<br>
Handelsregister: Amtsgericht Muenchen HRB 153243<br>
Geschäftsführer: Brendan Lane, Charlie Peters, Michael Cunningham,<br>
Werner Knoblich<br>
</div></div></blockquote></div><br>