Document fins/I0799-1
FIN #: I0799-1
SYNOPSIS: Ultra 5 and Ultra 10 systems require Solaris 8 10/00 (U2) or later to
support maximum parallel printer cable length
DATE: Mar/22/02
KEYWORDS: Ultra 5 and Ultra 10 systems require Solaris 8 10/00 (U2) or later to
support maximum parallel printer cable length
---------------------------------------------------------------------
- Sun Proprietary/Confidential: Internal Use Only -
---------------------------------------------------------------------
FIELD INFORMATION NOTICE
(For Authorized Distribution by SunService)
SYNOPSIS: Ultra 5 and Ultra 10 systems require Solaris 8 10/00 (U2) or
later to support maximum parallel printer cable length.
Sun Alert: No
TOP FIN/FCO REPORT: No
PRODUCT_REFERENCE: Printer cable length on U5/U10
PRODUCT CATEGORY: Desktop / Service
PRODUCTS AFFECTED:
Systems Affected
----------------
Mkt_ID Platform Model Description Serial Number
------ -------- ----- ----------- -------------
- A21 ALL Ultra 5 -
- A22 ALL Ultra 10 -
X-Options affected
------------------
Mkt_ID Platform Model Description Serial Number
------ -------- ----- ----------- -------------
- - - - -
PART NUMBERS AFFECTED:
Part Number Description Model
----------- ----------- -----
- - -
REFERENCES:
BugId: 4640829 - loss or garbled data with the printer at 25 feet.
PROBLEM DESCRIPTION:
Ultra 5/10 systems running an OS earlier than Solaris 8 10/00 (U2)
might experience data loss or garbled output to parallel printers when
printer cables longer than 10 feet (3 meters) are used. This problem
will not cause a down system but might result in unnecessary service
calls due to perceived printer, cable, or parallel port problems.
Ultra 5/10 systems running Solaris 2.5.1, 2.6, and 7 are also affected.
To determine the OS release for an Ultra 5/10 system run this command:
# cat /etc/release
Solaris 8 10/00 s28s_u2wos_11b SPARC
IEEE 1284 specifies two levels of compliance for an electrical
interface. Level 1 devices are designed to operate over a maximum
cable length of 10 feet (3 meters). Level 2 devices can operate over a
maximum cable length of 33 feet (10 meters). Peripherals at the other
end of the cable should also meet level 2 requirements to use cables
longer than 10 feet. Ultra 5 and Ultra 10 parallel ports are level 2
compliant.
A limiting factor to printer cable length is the 1284 mode in use, that
is, Nibble mode, ECP mode, or Compatibility mode. Nibble mode and ECP
modes are interlocked protocols which are independent of cable length.
Compatibility mode, on the other hand, is not interlocked and has
certain timing requirements which make cable length a factor.
The parallel port driver in releases prior to Solaris 8 10/00 only
supports Compatibility mode, hence the maximum printer cable length is
limited to 10 feet. To operate beyond 10 feet up to the level 2 device
spec limit of 33 feet, the platform must have Solaris 8 10/00 or later
installed.
IMPLEMENTATION:
---
| | MANDATORY (Fully Proactive)
---
---
| | CONTROLLED PROACTIVE (per Sun Geo Plan)
---
---
| X | REACTIVE (As Required)
---
CORRECTIVE ACTION:
The following recommendation is provided as a guideline for authorized
Enterprise Services Field Representatives who may encounter the above
mentioned problem.
If field personnel encounter a system with garbled or lost data to or
from a parallel printer AND the system's parallel printer cable is
longer than 10 feet (3 meters), Solaris 8 10/00 (U2) or later should be
installed on the system or a shorter (less than 10 feet) printer cable
should be installed.
COMMENTS:
None
============================================================================
Implementation Footnote:
i) In case of MANDATORY FINs, Enterprise Services will attempt to
contact all affected customers to recommend implementation of
the FIN.
ii) For CONTROLLED PROACTIVE FINs, Enterprise Services mission critical
support teams will recommend implementation of the FIN (to their
respective accounts), at the convenience of the customer.
iii) For REACTIVE FINs, Enterprise Services will implement the FIN as the
need arises.
----------------------------------------------------------------------------
All released FINs and FCOs can be accessed using your favorite network
browser as follows:
SunWeb Access:
--------------
* Access the top level URL of http://sdpsweb.ebay/FIN_FCO/
* From there, select the appropriate link to query or browse the FIN and
FCO Homepage collections.
SunSolve Online Access:
-----------------------
* Access the SunSolve Online URL at http://sunsolve.Corp/
* From there, select the appropriate link to browse the FIN or FCO index.
Internet Access:
----------------
* Access the top level URL of https://infoserver.Sun.COM
--------------------------------------------------------------------------
General:
--------
* Send questions or comments to finfco-manager@sdpsweb.EBay
--------------------------------------------------------------------------
Copyright (c) 1997-2003 Sun Microsystems, Inc.