vcware and modemware Versions on AS5300 *&* GSR FRU info
Andrew Partan
asp at partan.com
Sun Jan 11 05:30:10 UTC 2004
On Fri, Jan 09, 2004 at 05:47:42PM +0200, Yuval Ben-Ari wrote:
> show modem version seems too long,
> you might want to monitor "show spe version"
>
> this routine will do it:
On Fri, Jan 09, 2004 at 06:44:40PM +0200, Yuval Ben-Ari wrote:
> I find it very useful for inventory purposes to include FRU information
> on GSR routers.
> I added the following to sub ShowDiag:
I merged these into rancid.in; can you (or someone) do a check of
these bits to make sure they still work & I didn't blow something?
Thanks,
--asp
-------------- next part --------------
#! @PERLV_PATH@
##
## $Id: rancid.in,v 1.167 2004/01/11 03:49:13 heas Exp $
##
## Copyright (C) 1997-2004 by Terrapin Communications, Inc.
## All rights reserved.
##
## This software may be freely copied, modified and redistributed
## without fee for non-commerical purposes provided that this license
## remains intact and unmodified with any RANCID distribution.
##
## There is no warranty or other guarantee of fitness of this software.
## It is provided solely "as is". The author(s) disclaim(s) all
## responsibility and liability with respect to this software's usage
## or its effect upon hardware, computer systems, other software, or
## anything else.
##
## Except where noted otherwise, rancid was written by and is maintained by
## Henry Kilmer, John Heasley, Andrew Partan, Pete Whiting, and Austin Schutz.
##
#
# RANCID - Really Awesome New Cisco confIg Differ
#
# usage: rancid [-d] [-l] [-f filename | $host]
#
use Getopt::Std;
getopts('dfl');
$log = $opt_l;
$debug = $opt_d;
$file = $opt_f;
$host = $ARGV[0];
$clean_run = 0;
$found_end = 0;
$timeo = 90; # clogin timeout in seconds
my(%filter_pwds); # password filtering mode
# This routine is used to print out the router configuration
sub ProcessHistory {
my($new_hist_tag,$new_command,$command_string, at string)=(@_);
if((($new_hist_tag ne $hist_tag) || ($new_command ne $command))
&& defined %history) {
print eval "$command \%history";
undef %history;
}
if (($new_hist_tag) && ($new_command) && ($command_string)) {
if ($history{$command_string}) {
$history{$command_string} = "$history{$command_string}@string";
} else {
$history{$command_string} = "@string";
}
} elsif (($new_hist_tag) && ($new_command)) {
$history{++$#history} = "@string";
} else {
print "@string";
}
$hist_tag = $new_hist_tag;
$command = $new_command;
1;
}
sub numerically { $a <=> $b; }
# This is a sort routing that will sort numerically on the
# keys of a hash as if it were a normal array.
sub keynsort {
local(%lines)=@_;
local($i) = 0;
local(@sorted_lines);
foreach $key (sort numerically keys(%lines)) {
$sorted_lines[$i] = $lines{$key};
$i++;
}
@sorted_lines;
}
# This is a sort routing that will sort on the
# keys of a hash as if it were a normal array.
sub keysort {
local(%lines)=@_;
local($i) = 0;
local(@sorted_lines);
foreach $key (sort keys(%lines)) {
$sorted_lines[$i] = $lines{$key};
$i++;
}
@sorted_lines;
}
# This is a sort routing that will sort on the
# values of a hash as if it were a normal array.
sub valsort{
local(%lines)=@_;
local($i) = 0;
local(@sorted_lines);
foreach $key (sort values %lines) {
$sorted_lines[$i] = $key;
$i++;
}
@sorted_lines;
}
# This is a numerical sort routing (ascending).
sub numsort {
local(%lines)=@_;
local($i) = 0;
local(@sorted_lines);
foreach $num (sort {$a <=> $b} keys %lines) {
$sorted_lines[$i] = $lines{$num};
$i++;
}
@sorted_lines;
}
# This is a sort routine that will sort on the
# ip address when the ip address is anywhere in
# the strings.
sub ipsort {
local(%lines)=@_;
local($i) = 0;
local(@sorted_lines);
foreach $addr (sort sortbyipaddr keys %lines) {
$sorted_lines[$i] = $lines{$addr};
$i++;
}
@sorted_lines;
}
# These two routines will sort based upon IP addresses
sub ipaddrval {
my(@a) = ($_[0] =~ m#^(\d+)\.(\d+)\.(\d+)\.(\d+)$#);
$a[3]+256*($a[2]+256*($a[1]+256*$a[0]));
}
sub sortbyipaddr {
&ipaddrval($a) <=> &ipaddrval($b);
}
# This routine parses "show version"
sub ShowVersion {
print STDERR " In ShowVersion: $_" if ($debug);
my($slaveslot);
while (<INPUT>) {
tr/\015//d;
last if(/^$prompt/);
next if(/^(\s*|\s*$cmd\s*)$/);
return(-1) if (/command authorization failed/i);
# the pager can not be disabled per-session on the PIX
s/^<-+ More -+>\s*//;
if (/^Slave in slot (\d+) is running/) {
$slave = " Slave:";
$slaveslot = ", slot $1";
next;
}
if (/^Application and Content Networking Software/) { $type="CE"; }
/^Application and Content Networking Software Release /i &&
ProcessHistory("COMMENTS","keysort","F1", "!Image: $_") && next;
/^Cisco Secure PIX /i &&
ProcessHistory("COMMENTS","keysort","F1", "!Image: $_") && next;
# PIX fail-over license
/^This PIX has an?\s+(.*)$/ &&
ProcessHistory("COMMENTS","keysort","C1", "!$_") && next;
/^(Cisco )?IOS .* Software,? \(([A-Za-z-0-9]*)\), .*Version\s+(.*)$/ &&
ProcessHistory("COMMENTS","keysort","F1",
"!Image:$slave Software: $2, $3\n") && next;
/^([A-Za-z-0-9_]*) Synced to mainline version: (.*)$/ &&
ProcessHistory("COMMENTS","keysort","F2",
"!Image:$slave $1 Synced to mainline version: $2\n") && next;
/^Compiled (.*)$/ &&
ProcessHistory("COMMENTS","keysort","F3",
"!Image:$slave Compiled: $1\n") && next;
/^ROM: (IOS \S+ )?(System )?Bootstrap.*(Version.*)$/ &&
ProcessHistory("COMMENTS","keysort","G1",
"!ROM Bootstrap: $3\n") && next;
if (/^Hardware:\s+(.*), (.* RAM), CPU (.*)$/) {
ProcessHistory("COMMENTS","keysort","A1",
"!Chassis type: $1 - a PIX\n");
ProcessHistory("COMMENTS","keysort","A2",
"!CPU: $3\n");
ProcessHistory("COMMENTS","keysort","B1", "!Memory: $2\n");
}
/^Serial Number:\s+(.*)$/ &&
ProcessHistory("COMMENTS","keysort","C1", "!$_") && next;
# CatOS 3500xl stuff
/^System serial number(:\s+.*)$/ &&
ProcessHistory("COMMENTS","keysort","C1", "!Serial Number$1\n") &&
next;
/^Model / &&
ProcessHistory("COMMENTS","keysort","C2", "!$_") && next;
/^Motherboard / &&
ProcessHistory("COMMENTS","keysort","C3", "!$_") && next;
/^Power supply / &&
ProcessHistory("COMMENTS","keysort","C4", "!$_") && next;
/^Activation Key:\s+(.*)$/ &&
ProcessHistory("COMMENTS","keysort","C2", "!$_") && next;
/^ROM: \d+ Bootstrap .*(Version.*)$/ &&
ProcessHistory("COMMENTS","keysort","G2",
"!ROM Image: Bootstrap $1\n!\n") && next;
/^ROM: .*(Version.*)$/ &&
ProcessHistory("COMMENTS","keysort","G3","!ROM Image: $1\n") && next;
/^BOOTFLASH: .*(Version.*)$/ &&
ProcessHistory("COMMENTS","keysort","G4","!BOOTFLASH: $1\n") && next;
/^BOOTLDR: .*(Version.*)$/ &&
ProcessHistory("COMMENTS","keysort","G4","!BOOTLDR: $1\n") && next;
/^System image file is "([^\"]*)", booted via (\S*)/ &&
# removed the booted source due to
# CSCdk28131: cycling info in 'sh ver'
# ProcessHistory("COMMENTS","keysort","F4","!Image: booted via $2, $1\n") &&
ProcessHistory("COMMENTS","keysort","F4","!Image: booted $1\n") &&
next;
/^System image file is "([^\"]*)"$/ &&
ProcessHistory("COMMENTS","keysort","F5","!Image: $1\n") && next;
if (/(\S+)\s+\((\S+)\)\s+processor.*with (\S+[kK]) bytes/) {
my($proc) = $1;
my($cpu) = $2;
my($mem) = $3;
my($device) = "router";
# the next line ought to be the more specific cpu info, grab it.
# yet, some boards/IOS vers have a processor ID line between these
# two. grrr. make sure we dont grab the "software" junk that
# follows these lines by looking for "CPU at " or the 2600s
# "processor: " unique string. there are undoubtedly many other
# incantations. for a slave, we dont get this info and its just a
# blank line.
$_ = <INPUT>;
$_ = <INPUT> if (/processor board id/i);
$_ = "" if (! /(cpu at |processor: |$cpu processor,)/i);
tr/\015//d;
s/implementation/impl/i;
if ($_ !~ /^\s*$/) {
chomp;
s/^/, /;
}
if ( $proc eq "CSC") {
$type = "AGS";
} elsif ( $proc eq "CSC4") {
$type = "AGS+";
} elsif ( $proc =~ /^(AS)?25[12][12]/) {
$type = "2500";
} elsif ( $proc =~ /261[01]/ || $proc =~ /262[01]/ ) {
$type = "2600";
} elsif ( $proc =~ /^36[0246][0-9]/) {
$type = "3600";
} elsif ( $proc =~ /^37/) {
$type = "3700";
} elsif ( $proc eq "RSP7000") {
$type = "7500";
} elsif ( $proc =~ /RSP\d/) {
$type = "7500";
} elsif ( $proc eq "RP1") {
$type = "7000";
} elsif ( $proc eq "RP") {
$type = "7000";
} elsif ( $proc =~ /720[246]/) {
$type = "7200";
} elsif ( $proc =~ /1200[48]\/GRP/ || $proc =~ /1201[26]\/GRP/) {
$type = "12000";
} elsif ( $proc =~ /1201[26]-8R\/GRP/) {
$type = "12000";
} elsif ( $proc =~ /WS-C29/) {
$type = "2900XL";
$device = "switch";
} elsif ( $proc =~ /WS-C355/) {
$type = "3550";
$device = "switch";
} elsif ( $proc =~ /WS-C35/) {
$type = "3500XL";
$device = "switch";
} elsif ( $proc =~ /WS-C45/) {
$type = "4500";
$device = "switch";
} elsif ( $proc =~ /6000/) {
$type = "6000";
$device = "switch";
} elsif ( $proc =~ /CISCO76/) {
$type = "7600";
$device = "router";
} elsif ( $proc =~ /1900/) {
$type = "1900";
$device = "switch";
} else {
$type = $proc;
}
print STDERR "TYPE = $type\n" if ($debug);
ProcessHistory("COMMENTS","keysort","A1",
"!Chassis type:$slave $proc - a $type $device\n");
ProcessHistory("COMMENTS","keysort","B1",
"!Memory:$slave main $mem\n");
ProcessHistory("COMMENTS","keysort","A3","!CPU:$slave $cpu$_$slaveslot\n");
next;
}
if (/(\S+) Silicon\s*Switch Processor/) {
if (!defined($C0)) {
$C0=1; ProcessHistory("COMMENTS","keysort","C0","!\n");
}
ProcessHistory("COMMENTS","keysort","C2","!SSP: $1\n");
$ssp = 1;
$sspmem = $1;
next;
}
/^(\d+[kK]) bytes of multibus/ &&
ProcessHistory("COMMENTS","keysort","B2",
"!Memory: multibus $1\n") && next;
/^(\d+[kK]) bytes of (non-volatile|NVRAM)/ &&
ProcessHistory("COMMENTS","keysort","B3",
"!Memory: nvram $1\n") && next;
/^(\d+[kK]) bytes of flash memory/ &&
ProcessHistory("COMMENTS","keysort","B5","!Memory: flash $1\n") &&
next;
/^(\d+[kK]) bytes of .*flash partition/ &&
ProcessHistory("COMMENTS","keysort","B6",
"!Memory: flash partition $1\n") && next;
/^(\d+[kK]) bytes of Flash internal/ &&
ProcessHistory("COMMENTS","keysort","B4",
"!Memory: bootflash $1\n") && next;
if(/^(\d+[kK]) bytes of (Flash|ATA)?.*PCMCIA .*(slot|disk) ?(\d)/i) {
ProcessHistory("COMMENTS","keysort","B7",
"!Memory: pcmcia $2 $3$4 $1\n");
next;
}
if(/^WARNING/) {
if (!defined($I0)) {
$I0=1;
ProcessHistory("COMMENTS","keysort","I0","!\n");
}
ProcessHistory("COMMENTS","keysort","I1","! $_");
}
if (/^Configuration register is (.*)$/) {
$config_register=$1;
next;
}
}
return(0);
}
# This routine parses "show redundancy"
sub ShowRedundancy {
print STDERR " In ShowRedundancy: $_" if ($debug);
while (<INPUT>) {
tr/\015//d;
last if(/^$prompt/);
next if(/^(\s*|\s*$cmd\s*)$/);
# the pager can not be disabled per-session on the PIX
s/^<-+ More -+>\s*//;
/^IOS .* Software \(([A-Za-z-0-9]*)\), .*Version\s+(.*)$/ &&
ProcessHistory("COMMENTS","keysort","F1",
"!Image:$slave Software: $1, $2\n") && next;
/^Compiled (.*)$/ &&
ProcessHistory("COMMENTS","keysort","F3",
"!Image:$slave Compiled: $1\n") && next;
}
return(0);
}
# This routine parses "show IDprom"
sub ShowIDprom {
my($tmp);
print STDERR " In ShowIDprom: $_" if ($debug);
while (<INPUT>) {
tr/\015//d;
last if(/^$prompt/);
next if(/^(\s*|\s*$cmd\s*)$/);
# the pager can not be disabled per-session on the PIX
s/^<-+ More -+>\s*//;
/FRU is .(.*)\'/ && ($tmp = $1);
/Product Number = .(.*)\'/ &&
ProcessHistory("COMMENTS","keysort","D0","!\n") &&
ProcessHistory("COMMENTS","keysort","D0",
"!Catalyst Chassis type: $1, $tmp\n");
/Serial Number = .([0-9A-Za-z]+)/ &&
ProcessHistory("COMMENTS","keysort","D1",
"!Catalyst Chassis S/N: $1\n");
/Manufacturing Assembly Number = .([-0-9]+)/ && ($tmp = $1);
/Manufacturing Assembly Revision = .(.*)\'/ && ($tmp .= ", rev " . $1);
/Hardware Revision = ([0-9.]+)/ &&
ProcessHistory("COMMENTS","keysort","D2",
"!Catalyst Chassis assembly: $tmp, ver $1\n");
}
return(0);
}
# This routine parses "show install active"
sub ShowInstallActive {
print STDERR " In ShowInstallActive: $_" if ($debug);
while (<INPUT>) {
tr/\015//d;
last if (/^$prompt/);
next if (/^(\s*|\s*$cmd\s*)$/);
return(1) if /^\s*\^\s*$/;
return(1) if /(Invalid input detected|Type help or )/;
return(-1) if (/command authorization failed/i);
# the pager can not be disabled per-session on the PIX
s/^<-+ More -+>\s*//;
ProcessHistory("COMMENTS","keysort","F5","!Image: $_") && next;
}
return(0);
}
# This routine parses "show env all"
sub ShowEnv {
# Skip if this is not a 7500, 7200, or 7000.
print STDERR " In ShowEnv: $_" if ($debug);
while (<INPUT>) {
tr/\015//d;
last if (/^$prompt/);
next if (/^(\s*|\s*$cmd\s*)$/);
#return(1) if ($type !~ /^7/);
return(-1) if (/command authorization failed/i);
# the pager can not be disabled per-session on the PIX
s/^<-+ More -+>\s*//;
if (!defined($E0)) {
$E0=1;
ProcessHistory("COMMENTS","keysort","E0","!\n");
}
if (/^Arbiter type (\d), backplane type (\S+)/) {
if (!defined($C0)) {
$C0=1; ProcessHistory("COMMENTS","keysort","C0","!\n");
}
ProcessHistory("COMMENTS","keysort","C1",
"!Enviromental Arbiter Type: $1\n");
ProcessHistory("COMMENTS","keysort","A2",
"!Chassis type: $2 backplane\n");
next;
}
/^\s*(Power [^:\n]+)$/ &&
ProcessHistory("COMMENTS","keysort","E1","!Power: $1\n") && next;
/^\s*(Lower Power .*)/i &&
ProcessHistory("COMMENTS","keysort","E2","!Power: $1\n") && next;
/^\s*(redundant .*)/i &&
ProcessHistory("COMMENTS","keysort","E2","!Power: $1\n") && next;
/^\s*(RPS is .*)/i &&
ProcessHistory("COMMENTS","keysort","E2","!Power: $1\n") && next;
}
ProcessHistory("COMMENTS","","","!\n");
return(0);
}
# This routine parses "show rsp chassis-info" for the rsp
# This will create arrays for hw info.
sub ShowRSP {
print STDERR " In ShowRSP: $_" if ($debug);
while (<INPUT>) {
tr/\015//d;
last if (/^$prompt/);
next if (/^(\s*|\s*$cmd\s*)$/);
return(-1) if (/command authorization failed/i);
# return(1) if ($type !~ /^12[40]/);
# the pager can not be disabled per-session on the PIX
s/^<-+ More -+>\s*//;
/^$/ && next;
/^\s+Chassis model: (\S+)/ &&
ProcessHistory("COMMENTS","keysort","D0","!\n") &&
ProcessHistory("COMMENTS","keysort","D1",
"!RSP Chassis model: $1\n") &&
next;
/^\s+Chassis S\/N: (.*)$/ &&
ProcessHistory("COMMENTS","keysort","D2",
"!RSP Chassis S/N: $1\n") &&
next;
}
return(0);
}
# This routine parses "show gsr chassis-info" for the gsr
# This will create arrays for hw info.
sub ShowGSR {
# Skip if this is not a 1200n.
print STDERR " In ShowGSR: $_" if ($debug);
while (<INPUT>) {
tr/\015//d;
last if (/^$prompt/);
next if (/^(\s*|\s*$cmd\s*)$/);
return(-1) if (/command authorization failed/i);
# return(1) if ($type !~ /^12[40]/);
# the pager can not be disabled per-session on the PIX
s/^<-+ More -+>\s*//;
/^$/ && next;
/^\s+Chassis: type (\S+) Fab Ver: (\S+)/ &&
ProcessHistory("COMMENTS","keysort","D0","!\n") &&
ProcessHistory("COMMENTS","keysort","D1",
"!GSR Chassis type: $1 Fab Ver: $2\n") &&
next;
/^\s+Chassis S\/N: (.*)$/ &&
ProcessHistory("COMMENTS","keysort","D2",
"!GSR Chassis S/N: $1\n") &&
next;
/^\s+PCA: (\S+)\s*rev: (\S+)\s*dev: \S+\s*HW ver: (\S+)$/ &&
ProcessHistory("COMMENTS","keysort","D3",
"!GSR Backplane PCA: $1, rev $2, ver $3\n") &&
next;
/^\s+Backplane S\/N: (\S+)$/ &&
ProcessHistory("COMMENTS","keysort","D4",
"!GSR Backplane S/N: $1\n") &&
next;
}
ProcessHistory("COMMENTS","","","!\n");
return(0);
}
# This routine parses "show boot"
sub ShowBoot {
# Pick up boot variables if 7000/7200/7500/12000/2900/3500;
# otherwise pick up bootflash.
print STDERR " In ShowBoot: $_" if ($debug);
while (<INPUT>) {
tr/\015//d;
last if (/^$prompt/);
next if (/^(\s*|\s*$cmd\s*)$/);
return(1) if /^\s*\^\s*$/;
return(-1) if (/command authorization failed/i);
return(1) if /Ambiguous command/i;
return(1) if /(Invalid input detected|Type help or )/;
return(1) if /(Open device \S+ failed|Error opening \S+:)/;
# the pager can not be disabled per-session on the PIX
s/^<-+ More -+>\s*//;
next if /CONFGEN variable/;
if (!defined($H0)) {
$H0=1; ProcessHistory("COMMENTS","keysort","H0","!\n");
}
if ($type !~ /^(12[04]|7)/) {
if ($type !~ /^(29|35)00/) {
ProcessHistory("COMMENTS","keysort","H2","!BootFlash: $_");
} else {
ProcessHistory("COMMENTS","keysort","H1","!Variable: $_");
}
} elsif (/variable/) {
ProcessHistory("COMMENTS","keysort","H1","!Variable: $_");
}
}
ProcessHistory("COMMENTS","","","!\n");
return(0);
}
# This routine parses "show flash"
sub ShowFlash {
# skip if this is 7000, 7200, 7500, or 12000; else we end up with
# redundant data from dir /all slot0:
print STDERR " In ShowFlash: $_" if ($debug);
while (<INPUT>) {
tr/\015//d;
last if (/^$prompt/);
next if (/^(\s*|\s*$cmd\s*)$/);
return(1) if ($type =~ /^(12[40]|7)/);
return(-1) if (/command authorization failed/i);
return(1) if /^\s*\^\s*$/;
return(1) if /(Invalid input detected|Type help or )/;
# the pager can not be disabled per-session on the PIX
s/^<-+ More -+>\s*//;
ProcessHistory("FLASH","","","!Flash: $_");
}
ProcessHistory("","","","!\n");
return;
}
# This routine parses "dir /all ((disk|slot)N|bootflash|nvram):"
sub DirSlotN {
# Skip if this is not a 3600, 7000, 7200, 7500, or 12000.
print STDERR " In DirSlotN: $_" if ($debug);
my($dev) = (/\s([^\s]+):/);
while (<INPUT>) {
tr/\015//d;
last if (/^$prompt/);
next if (/^(\s*|\s*$cmd\s*)$/);
# return(1) if ($type !~ /^(12[40]|7|36)/);
return(1) if /^\s*\^\s*$/;
return(1) if /(Invalid input detected|Type help or )/;
return(1) if /(No such device|Error Sending Request)/i;
return(1) if /\%Error: No such file or directory/;
return(1) if /No space information available/;
return(-1) if /\%Error calling/;
return(-1) if /(: device being squeezed|ATA_Status time out)/i; # busy
return(-1) if (/command authorization failed/i);
return(1) if /(Open device \S+ failed|Error opening \S+:)/;
# the pager can not be disabled per-session on the PIX
s/^<-+ More -+>\s*//;
ProcessHistory("FLASH","","","!Flash: $dev: $_");
}
ProcessHistory("","","","!\n");
return(0);
}
# This routine parses "show controllers"
sub ShowContAll {
# Skip if this is a 70[01]0, 7500, or 12000.
print STDERR " In ShowContAll: $_" if ($debug);
while (<INPUT>) {
tr/\015//d;
last if (/^$prompt/);
next if (/^(\s*|\s*$cmd\s*)$/);
# return(1) if ($type =~ /^(12[40]|7[05])/);
return(-1) if (/command authorization failed/i);
# the pager can not be disabled per-session on the PIX
s/^<-+ More -+>\s*//;
if (/^Interface ([^ \n(]*)/) { $INT = "$1, "; next; }
/^(BRI unit \d)/ &&
ProcessHistory("INT","","","!Interface: $1\n") && next;
/^LANCE unit \d, NIM/ &&
ProcessHistory("INT","","","!Interface: $_") && next;
/^(LANCE unit \d)/ &&
ProcessHistory("INT","","","!Interface: $1\n") && next;
/(Media Type is \S+),/ &&
ProcessHistory("INT","","","!\t$1\n");
if (/(M\dT[^ :]*:) show controller:$/) {
my($ctlr) = $1;
$_ = <INPUT>; tr/\015//d; s/ subunit \d,//;
ProcessHistory("INT","","","!Interface: $ctlr $_");
}
if (/^(\S+) : show controller:$/) {
my($ctlr) = $1;
$_ = <INPUT>; tr/\015//d; s/ subunit \d,//;
ProcessHistory("INT","","","!Interface: $ctlr: $_");
}
/^(HD unit \d), idb/ &&
ProcessHistory("INT","","","!Interface: $1\n") && next;
/^HD unit \d, NIM/ &&
ProcessHistory("INT","","","!Interface: $_") && next;
/^buffer size \d+ HD unit \d, (.*)/ &&
ProcessHistory("INT","","","!\t$1\n") && next;
/^AM79970 / && ProcessHistory("INT","","","!Interface: $_") && next;
/^buffer size \d+ (Universal Serial: .*)/ &&
ProcessHistory("INT","","","!\t$1\n") && next;
/^Hardware is (.*)/ &&
ProcessHistory("INT","","","!Interface: $INT$1\n") && next;
/^(QUICC Serial unit \d),/ &&
ProcessHistory("INT","","","!$1\n") && next;
/^QUICC Ethernet .*/ &&
ProcessHistory("INT","","","!$_") && next;
/^DTE .*\.$/ &&
ProcessHistory("INT","","","!\t$_") && next;
/^(cable type :.*),/ &&
ProcessHistory("INT","","","!\t$1\n") && next;
/^(.* cable.*), received clockrate \d+$/ &&
ProcessHistory("INT","","","!\t$1\n") && next;
/^.* cable.*$/ &&
ProcessHistory("INT","","","!\t$_") && next;
}
return(0);
}
# This routine parses "show controllers cbus"
# Some of this is printed out in ShowDiagbus.
sub ShowContCbus {
# Skip if this is not a 7000 or 7500.
print STDERR " In ShowContCbus: $_" if ($debug);
while (<INPUT>) {
tr/\015//d;
last if (/^$prompt/);
next if (/^(\s*|\s*$cmd\s*)$/);
#return(1) if ($type !~ /^7[05]0/);
return(-1) if (/command authorization failed/i);
# the pager can not be disabled per-session on the PIX
s/^<-+ More -+>\s*//;
if (/^\s*slot(\d+): ([^,]+), hw (\S+), sw (\S+), ccb/) {
$slot = $1;
$board{$slot} = $2;
$hwver{$slot} = $3;
$hwucode{$slot} = $4;
} elsif (/^\s*(\S+) (\d+), hardware version (\S+), microcode version (\S+)/) {
$slot = $2;
$board{$slot} = $1;
$hwver{$slot} = $3;
$hwucode{$slot} = $4;
} elsif (/(Microcode .*)/) {
$ucode{$slot} = $1;
} elsif (/(software loaded .*)/) {
$ucode{$slot} = $1;
} elsif (/(\d+) Kbytes of main memory, (\d+) Kbytes cache memory/) {
$hwmemd{$slot} = $1;
$hwmemc{$slot} = $2;
} elsif (/byte buffers/) {
chop;
s/^\s*//;
$hwbuf{$slot} = $_;
} elsif (/Interface (\d+) - (\S+ \S+),/) {
$interface = $1;
ProcessHistory("HW","","",
"!\n!Int $interface: in slot $slot, named $2\n"); next;
} elsif (/(\d+) buffer RX queue threshold, (\d+) buffer TX queue limit, buffer size (\d+)/) {
ProcessHistory("HW","","","!Int $interface: rxq $1, txq $2, bufsize $3\n");
next;
}
}
return(0);
}
# This routine parses "show diagbus"
# This will create arrarys for hw info.
sub ShowDiagbus {
# Skip if this is not a 7000, 70[01]0, or 7500.
print STDERR " In ShowDiagbus: $_" if ($debug);
while (<INPUT>) {
tr/\015//d;
last if (/^$prompt/);
next if (/^(\s*|\s*$cmd\s*)$/);
#return(1) if ($type !~ /^7[05]/);
return(-1) if (/command authorization failed/i);
# the pager can not be disabled per-session on the PIX
s/^<-+ More -+>\s*//;
if (/^\s*Slot (\d+):/i) {
$slot = $1;
next;
} elsif (/^\s*Slot (\d+) \(virtual\):/i) {
$slot = $1;
next;
} elsif (/^\s*(.*Processor.*|.*controller|.*controler|.*Chassis Interface)(, FRU\s?:.*)?, HW rev (\S+), board revision (\S+)/i) {
$board = $1;
$hwver = $3;
$boardrev = $4;
if ($board =~ /Processor/) {
if ($board =~ /7000 Route\/Switch/) {
$board = "RSP7000";
} elsif ($board =~ /Route\/Switch Processor (\d)/) {
$board = "RSP$1";
} elsif ($board =~ /Route/) {
$board = "RP";
} elsif ($board =~ /Silicon Switch/) {
$board = "SSP";
} elsif ($board =~ /Switch/) {
$board = "SP";
$board = "SSP $sspmem" if $ssp;
} elsif ($board =~ /ATM/) {
$board = "AIP";
}
} elsif ($board =~ /(.*) controller/i) {
$board = $1;
}
# hwucode{$slot} defined in ShowContCbus
if (defined $hwucode{$slot}) {
ProcessHistory("SLOT","","","!\n!Slot $slot/$board: hvers $hwver rev $boardrev ucode $hwucode{$slot}\n");
} else {
ProcessHistory("SLOT","","","!\n!Slot $slot/$board: hvers $hwver rev $boardrev\n");
}
# These are also from the ShowContCbus
ProcessHistory("SLOT","","","!Slot $slot/$board: $ucode{$slot}\n") if (defined $ucode{$slot});
ProcessHistory("SLOT","","","!Slot $slot/$board: memd $hwmemd{$slot}, cache $hwmemc{$slot}\n")
if ((defined $hwmemd{$slot}) && (defined $hwmemc{$slot}));
ProcessHistory("SLOT","","","!Slot $slot/$board: $hwbuf{$slot}\n") if (defined $hwbuf{$slot});
next;
}
/Serial number: (\S+)\s*Part number: (\S+)/ &&
ProcessHistory("SLOT","","",
"!Slot $slot/$board: part $2, serial $1\n") &&
next;
/^\s*Controller Memory Size: (.*)$/ &&
ProcessHistory("SLOT","","","!Slot $slot/$board: $1\n") &&
next;
if (/PA Bay (\d) Information/) {
$pano = $1;
if ("PA" =~ /$board/) {
($s,$c) = split(/\//,$board);
$board = "$s/$c/PA $pano";
} else {
$board =~ s/\/PA \d//;
$board = "$board/PA $pano";
}
next;
}
/\s+(.*) (IP|PA), (\d) ports?,( \S+,)? (FRU\s?: )?(\S+)/ &&
ProcessHistory("SLOT","","","!Slot $slot/$board: type $6, $3 ports\n") &&
next;
/\s+(.*) (IP|PA)( \(\S+\))?, (\d) ports?/ &&
ProcessHistory("SLOT","","","!Slot $slot/$board: type $1$3, $4 ports\n") &&
next;
/^\s*HW rev (\S+), Board revision (\S+)/ &&
ProcessHistory("SLOT","","","!Slot $slot/$board: hvers $1 rev $2\n") &&
next;
/Serial number: (\S+)\s*Part number: (\S+)/ &&
ProcessHistory("SLOT","","","!Slot $slot/$board: part $2, serial $1\n") && next;
}
return(0);
}
# This routine parses "show diag" for the gsr, 7200, 3700, 3600, 2600.
# This will create arrarys for hw info.
sub ShowDiag {
# Skip if this is not a 12000.
print STDERR " In ShowDiag: $_" if ($debug);
while (<INPUT>) {
tr/\015//d;
last if (/^$prompt/);
next if (/^(\s*|\s*$cmd\s*)$/);
# return(1) if ($type !~ /^(12[40]|720|36|26)/);
return(-1) if (/command authorization failed/i);
/^$/ && next;
# the pager can not be disabled per-session on the PIX
s/^<-+ More -+>\s*//;
s/Port Packet Over SONET/POS/;
if (/^\s*SLOT\s+(\d+)\s+\((.*)\): (.*)/) {
$slot = $1;
ProcessHistory("SLOT","","","!\n");
ProcessHistory("SLOT","keysort","A","!Slot $slot: $3\n");
next;
}
if (/^\s+MAIN:\s* type \d+,\s+(.*)/) {
ProcessHistory("SLOT","keysort","AM","!Slot $slot/MAIN: part $1\n");
next;
}
if (/^c3700\s+(io-board|mid-plane)/i) {
$slot=$1;
ProcessHistory("SLOT","","","!\n");
ProcessHistory("SLOT","keysort","A","!Slot $slot: part $1\n");
next;
}
if (/ Engine:\s+(.*)/) {
ProcessHistory("SLOT","keysort","AE","!Slot $slot/Engine: $1\n");
}
if (/^\s+PCA:\s+(.*)/) {
local($part) = $1;
$_ = <INPUT>;
/^\s+(HW version|design release) (\S+)\s+S\/N (\S+)/i &&
ProcessHistory("SLOT","keysort","C1","!Slot $slot/PCA: part $part, serial $3\n") &&
ProcessHistory("SLOT","keysort","C2","!Slot $slot/PCA: hvers $2\n");
next;
}
if (/^\s+MBUS: .*\)\s+(.*)/) {
local($tmp) = "!Slot $slot/MBUS: part $1";
$_ = <INPUT>;
/^\s+HW version (\S+)\s+S\/N (\S+)/ &&
ProcessHistory("SLOT","keysort","MB1","$tmp, serial $2\n") &&
ProcessHistory("SLOT","keysort","MB2","!Slot $slot/MBUS: hvers $1\n");
next;
}
if (/^\s+MBUS Agent Software version (.*)/) {
ProcessHistory("SLOT","keysort","MB3","!Slot $slot/MBUS: software $1\n");
next;
}
if (/^\s+ROM Monitor version (.*)/) {
ProcessHistory("SLOT","keysort","R","!Slot $slot/ROM Monitor: version $1\n");
next;
}
if (/^\s+Fabric Downloader version used (.*)/) {
ProcessHistory("SLOT","keysort","Z","!Slot $slot/Fabric Downloader: version $1\n");
next;
}
if (/^\s+DRAM size: (\d+)/) {
local($dram) = $1 / 1048576;
$_ = <INPUT>;
if (/^\s+FrFab SDRAM size: (\d+)/) {
ProcessHistory("SLOT","keysort","MB4","!Slot $slot/MBUS: $dram Mbytes DRAM, "
. $1 / 1024 . " Kbytes SDRAM\n");
} else {
ProcessHistory("SLOT","keysort","MB4","!Slot $slot/MBUS: $dram Mbytes DRAM\n");
}
next;
}
if (/FRU:\s+Linecard\/Module:\s+(\S+)/) {
ProcessHistory("SLOT","","","!Slot $slot/FRU: Linecard/Module: $1\n")
next;
}
# 7200, 3600, 2600, and 1700 stuff
if (/^(Slot)\s+(\d+(\/\d+)?):/
|| /^\s+(WIC|VIC|WIC\/VIC) Slot (\d):/
|| /^(Encryption AIM) (\d):/) {
if ($1 eq "WIC") {
$WIC = "/$2";
} elsif ($1 eq "VIC") {
$WIC = "/$2";
} elsif ($1 eq "WIC/VIC") {
$WIC = "/$2";
} elsif ($1 eq "Encryption AIM") {
$slot = "$2";
undef($WIC);
ProcessHistory("SLOT","","","!\n");
ProcessHistory("SLOT","keysort","B","!Slot $slot: type $1\n");
next;
} else {
$slot = $2;
undef($WIC);
}
$_ = <INPUT>; tr/\015//d;
# clean up hideous 7200/etc formats to look more like 7500 output
s/Fast-ethernet on C7200 I\/O card/FE-IO/;
s/ with MII or RJ45/-TX/;
s/Fast-ethernet /100Base/; s/[)(]//g;
s/intermediate reach/IR/i;
ProcessHistory("SLOT","","","!\n");
/\s+(.*) port adapter,?\s+(\d+)\s+/i &&
ProcessHistory("SLOT","keysort","B","!Slot $slot: type $1, $2 ports\n") && next;
# I/O controller with no interfaces
/\s+(.*)\s+port adapter\s*$/i &&
ProcessHistory("SLOT","keysort","B","!Slot $slot: type $1, 0 ports\n") && next;
/\s+(.*)\s+daughter card(.*)$/ &&
ProcessHistory("SLOT","keysort","B","!Slot $slot$WIC: type $1$2\n") && next;
/\s+(FT1)$/ &&
ProcessHistory("SLOT","keysort","B","!Slot $slot$WIC: type $1\n") && next;
# handle WICs lacking "daughter card" in the 2nd line of their
# show diag o/p
if (defined($WIC)) {
s/^\s+//;
ProcessHistory("SLOT","keysort","B","!Slot $slot$WIC: type $_");
}
next;
}
# yet another format. seen on 2600s w/ 12.1, but appears to be all
# 12.1, including 7200s & 3700s. Sometimes the PCB serial appears
# before the hardware revision.
if (/(pcb serial number|hardware revision)\s+:\s+(\S+)$/i) {
my($hw, $pn, $rev, $sn);
if ($1 =~ /^pcb/i) {
$sn = $2;
} else {
$hw = $2;
}
while (<INPUT>) {
tr/\015//d;
if (/0x..: /) {
# no effing idea why break does not work there
goto PerlSucks;
}
if (/hardware revision\s+:\s+(\S+)/i) { $hw = $1; }
if (/part number\s+:\s+(\S+)/i) { $pn = $1; }
if (/board revision\s+:\s+(\S+)/i) { $rev = $1; }
if (/pcb serial number\s+:\s+(\S+)/i) { $sn = $1; }
}
PerlSucks:
ProcessHistory("SLOT","keysort","B","!Slot $slot$WIC: hvers $hw rev $rev\n");
ProcessHistory("SLOT","keysort","C","!Slot $slot$WIC: part $pn, serial $sn\n");
}
/revision\s+(\S+).*revision\s+(\S+)/ &&
ProcessHistory("SLOT","keysort","C","!Slot $slot$WIC: hvers $1 rev $2\n") &&
next;
/number\s+(\S+)\s+Part number\s+(\S+)/ &&
ProcessHistory("SLOT","keysort","D","!Slot $slot$WIC: part $2, serial $1\n") &&
next;
}
ProcessHistory("SLOT","","","!\n");
return(0);
}
# This routine parses "show module".
sub ShowModule {
print STDERR " In ShowModule: $_" if ($debug);
my(@lines);
my($slot);
while (<INPUT>) {
tr/\015//d;
return if (/^\s*\^$/);
last if (/^$prompt/);
next if (/^(\s*|\s*$cmd\s*)$/);
return(-1) if (/command authorization failed/i);
# the pager can not be disabled per-session on the PIX
s/^<-+ More -+>\s*//;
# match slot/card info line
if (/^ *(\d+)\s+(\d+)\s+(.*)\s+(\S+)\s+(\S+)\s*$/) {
$lines[$1] .= "!Slot $1: type $3, $2 ports\n!Slot $1: part $4, serial $5\n";
$lines[$1] =~ s/\s+,/,/g;
}
# now match the Revs in the second paragraph of o/p and stick it in
# the array with the previous bits...grumble.
if (/^ *(\d+)\s+\S+\s+to\s+\S+\s+(\S+)\s+(\S*)\s+(\S+)(\s+\S+)?\s*$/) {
$lines[$1] .= "!Slot $1: hvers $2, firmware $3, sw $4\n";
$lines[$1] =~ s/\s+,/,/g;
}
}
foreach $slot (@lines) {
next if ($slot =~ /^\s*$/);
ProcessHistory("Module","","","$slot!\n");
}
return(0);
}
# This routine parses "show spe version".
sub ShowSpeVersion {
print STDERR " In ShowSpeVersion: $_" if ($debug);
while (<INPUT>) {
tr/\015//d;
last if (/^$prompt/);
next if (/^(\s*|\s*$cmd\s*)$/);
return(1) if /^\s*\^\s*$/;
return(1) if /(Invalid input detected|Type help or )/;
return(-1) if (/command authorization failed/i);
ProcessHistory("MODEM","","","!Modem: $_") && next;
}
ProcessHistory("MODEM","","","!\n");
return(0);
}
# This routine parses "show c7200" for the 7200
# This will create arrays for hw info.
sub ShowC7200 {
# Skip if this is not a 7200.
print STDERR " In ShowC7200: $_" if ($debug);
while (<INPUT>) {
tr/\015//d;
last if (/^$prompt/);
next if (/^(\s*|\s*$cmd\s*)$/);
#return(1) if ($type !~ /^72/);
return(-1) if (/command authorization failed/i);
/^$/ && next;
# the pager can not be disabled per-session on the PIX
s/^<-+ More -+>\s*//;
if (/^(C7200 )?Midplane EEPROM:/) {
$_ = <INPUT>;
/revision\s+(\S+).*revision\s+(\S+)/;
ProcessHistory("SLOT","","","!Slot Midplane: hvers $1 rev $2\n");
$_ = <INPUT>;
/number\s+(\S+)\s+Part number\s+(\S+)/;
ProcessHistory("SLOT","","","!Slot Midplane: part $2, serial $1\n!\n");
next;
}
if (/C720\d(VXR)? CPU EEPROM:/) {
my ($hvers,$rev,$part,$serial);
# npe400s report their cpu eeprom info differently w/ 12.0.21S
while (<INPUT>) {
/Hardware Revision\s+: (\S+)/ && ($hvers = $1) && next;
/Board Revision\s+: (\S+)/ && ($rev = $1) && next;
/Part Number\s+: (\S+)/ && ($part = $1) && next;
/Serial Number\s+: (\S+)/ && ($serial = $1) && next;
/revision\s+(\S+).*revision\s+(\S+)/ &&
($hvers = $1, $rev = $2) && next;
/number\s+(\S+)\s+Part number\s+(\S+)/ &&
($serial = $1, $part = $2) && next;
/^\s*$/ && last;
}
ProcessHistory("SLOT","","","!Slot CPU: hvers $hvers rev $rev\n");
ProcessHistory("SLOT","","","!Slot CPU: part $part, serial $serial\n!\n");
next;
}
}
return(0);
}
# This routine parses "show vtp status"
sub ShowVTP {
print STDERR " In ShowVTP: $_" if ($debug);
while (<INPUT>) {
tr/\015//d;
last if (/^$prompt/);
next if (/^(\s*|\s*$cmd\s*)$/);
return(1) if /^\s*\^\s*$/;
return(1) if /(Invalid input detected|Type help or )/;
#return(1) if ($type !~ /^(2900XL|3500XL|6000)$/);
return(-1) if (/command authorization failed/i);
next if (/^Configuration last modified by/);
# the pager can not be disabled per-session on the PIX
s/^<-+ More -+>\s*//;
if (/^VTP Operating Mode\s+:\s+(Transparent|Server)/) {
$DO_SHOW_VLAN = 1;
}
ProcessHistory("COMMENTS","keysort","I0","!VTP: $_");
}
ProcessHistory("COMMENTS","keysort","I0","!\n");
return(0);
}
# This routine parses "show vlan"
sub ShowVLAN {
print STDERR " In ShowVLAN: $_" if ($debug);
($_=<INPUT>,return(1)) if (!$DO_SHOW_VLAN);
while (<INPUT>) {
tr/\015//d;
last if (/^$prompt/);
next if (/^(\s*|\s*$cmd\s*)$/);
return(1) if /(Invalid input detected|Type help or )/;
# newer releases (~12.1(9)) place the vlan config in the normal
# configuration (write term).
return(1) if ($type =~ /^(3550|4500|7600)$/);
#return(1) if ($type !~ /^(2900XL|3500XL|6000)$/);
return(-1) if (/command authorization failed/i);
# the pager can not be disabled per-session on the PIX
s/^<-+ More -+>\s*//;
ProcessHistory("COMMENTS","keysort","IO","!VLAN: $_");
}
ProcessHistory("COMMENTS","keysort","IO","!\n");
return(0);
}
# This routine processes a "write term"
sub WriteTerm {
print STDERR " In WriteTerm: $_" if ($debug);
my($lineauto,$comment,$linecnt) = (0,0,0);
while (<INPUT>) {
tr/\015//d;
last if(/^$prompt/);
return(-1) if (/command authorization failed/i);
# the pager can not be disabled per-session on the PIX
s/^<-+ More -+>\s*//;
/Non-Volatile memory is in use/ && return(-1); # NvRAM is locked
return(0) if ($found_end); # Only do this routine once
$linecnt++;
$lineauto = 0 if (/^[^ ]/);
# skip the crap
if (/^(##+$|(Building|Current) configuration)/i) {
while (<INPUT>) {
next if (/^Current configuration\s*:/i);
next if (/^:/);
next if (/^([%!].*|\s*)$/);
next if (/^ip add.*ipv4:/); # band-aid for 3620 12.0S
last;
}
if (defined($config_register)) {
ProcessHistory("","","","!\nconfig-register $config_register\n");
}
tr/\015//d;
}
# some versions have other crap mixed in with the bits in the
# block above
/^! (Last configuration|NVRAM config last)/ && next;
# skip consecutive comment lines to avoid oscillating extra comment
# line on some access servers. grrr.
if (/^!/) {
next if ($comment);
ProcessHistory("","","",$_);
$comment++;
next;
}
$comment = 0;
# Dog gone Cool matches to process the rest of the config
/^tftp-server flash / && next; # kill any tftp remains
/^ntp clock-period / && next; # kill ntp clock-period
/^ length / && next; # kill length on serial lines
/^ width / && next; # kill width on serial lines
$lineauto = 1 if /^ modem auto/;
/^ speed / && $lineauto && next; # kill speed on serial lines
/^ clockrate / && next; # kill clockrate on serial interfaces
if (/^(enable )?(password|passwd) / && $filter_pwds >= 1) {
ProcessHistory("ENABLE","","","!$1$2 <removed>\n");
next;
}
if (/^(enable secret) / && $filter_pwds >= 2) {
ProcessHistory("ENABLE","","","!$1 <removed>\n");
next;
}
if (/^username (\S+)(\s.*)? secret /) {
if ($filter_pwds >= 2) {
ProcessHistory("USER","keysort","$1","!username $1$2 secret <removed>\n");
} else {
ProcessHistory("USER","keysort","$1","$_");
}
next;
}
if (/^username (\S+)(\s.*)? password ((\d) \S+|\S+)/) {
if ($filter_pwds == 2) {
ProcessHistory("USER","keysort","$1","!username $1$2 password <removed>\n");
} elsif ($filter_pwds == 1 && $4 ne "5"){
ProcessHistory("USER","keysort","$1","!username $1$2 password <removed>\n");
} else {
ProcessHistory("USER","keysort","$1","$_");
}
next;
}
if (/^( set session-key (in|out)bound ah \d+ )/ && $filter_pwds >= 1) {
ProcessHistory("","","","!$1<removed>\n");
next;
}
if (/^( set session-key (in|out)bound esp \d+ (authenticator|cypher) )/ && $filter_pwds >= 1) {
ProcessHistory("","","","!$1<removed>\n");
next;
}
if (/^(\s*)password / && $filter_pwds >= 1) {
ProcessHistory("LINE-PASS","","","!$1password <removed>\n");
next;
}
if (/^\s*neighbor (\S*) password / && $filter_pwds >= 1) {
ProcessHistory("","","","! neighbor $1 password <removed>\n");
next;
}
if (/^(ppp .* password) 7 .*/ && $filter_pwds >= 1) {
ProcessHistory("","","","!$1 <removed>\n"); next;
}
if (/^(ip ftp password) / && $filter_pwds >= 1) {
ProcessHistory("","","","!$1 <removed>\n"); next;
}
if (/^( ip ospf authentication-key) / && $filter_pwds >= 1) {
ProcessHistory("","","","!$1 <removed>\n"); next;
}
# isis passwords appear to be completely plain-text
if (/^\s+isis password (\S+)( .*)?/ && $filter_pwds >= 1) {
ProcessHistory("","","","!isis password <removed>$2\n"); next;
}
if (/^\s+(domain-password|area-password) (\S+)( .*)?/
&& $filter_pwds >= 1) {
ProcessHistory("","","","!$1 <removed>$3\n"); next;
}
# this is reversable, despite 'md5' in the cmd
if (/^( ip ospf message-digest-key \d+ md5) / && $filter_pwds >= 1) {
ProcessHistory("","","","!$1 <removed>\n"); next;
}
if (/^((crypto )?isakmp key) \S+ / && $filter_pwds >= 1) {
ProcessHistory("","","","!$1 <removed> $'"); next;
}
# filter HSRP passwords
if (/^(\s+standby \d authentication) / && $filter_pwds >= 1) {
ProcessHistory("","","","!$1 <removed>\n"); next;
}
# this appears in "measurement/sla" images
if (/^(\s+key-string \d?)/ && $filter_pwds >= 1) {
ProcessHistory("","","","!$1 <removed>\n"); next;
}
if (/^( l2tp tunnel \S+ password)/ && $filter_pwds >= 1) {
ProcessHistory("","","","!$1 <removed>\n"); next;
}
# i am told these are plain-text on the PIX
if (/^(vpdn username \S+ password)/ && $filter_pwds >= 1) {
ProcessHistory("","","","!$1 <removed>\n"); next;
}
if (/^( cable shared-secret ) / && $filter_pwds >= 1) {
ProcessHistory("","","","!$1 <removed>\n");
next;
}
/fair-queue individual-limit/ && next;
# sort ip explicit-paths.
if (/^ip explicit-path name (\S+)/) {
my($key) = $1;
my($expath) = $_;
while (<INPUT>) {
tr/\015//d;
last if (/^$prompt/);
last if (/^$prompt/ || ! /^(ip explicit-path name |[ !])/);
if (/^ip explicit-path name (\S+)/) {
ProcessHistory("EXPATH","keysort","$key","$expath");
$key = $1;
$expath = $_;
} else {
$expath .= $_;
}
}
ProcessHistory("EXPATH","keysort","$key","$expath");
}
# sort route-maps
if (/^route-map (\S+)/) {
my($key) = $1;
my($routemap) = $_;
while (<INPUT>) {
tr/\015//d;
last if (/^$prompt/ || ! /^(route-map |[ !])/);
if (/^route-map (\S+)/) {
ProcessHistory("ROUTEMAP","keysort","$key","$routemap");
$key = $1;
$routemap = $_;
} else {
$routemap .= $_;
}
}
ProcessHistory("ROUTEMAP","keysort","$key","$routemap");
}
# filter out any RCS/CVS tags to avoid confusing local CVS storage
s/\$(Revision|Id):/ $1:/;
# order access-lists
/^access-list\s+(\d\d?)\s+(\S+)\s+(\S+)/ &&
ProcessHistory("ACL $1 $2","ipsort","$3","$_") && next;
# order extended access-lists
/^access-list\s+(\d\d\d)\s+(\S+)\s+ip\s+host\s+(\S+)/ &&
ProcessHistory("EACL $1 $2","ipsort","$3","$_") && next;
/^access-list\s+(\d\d\d)\s+(\S+)\s+ip\s+(\d\S+)/ &&
ProcessHistory("EACL $1 $2","ipsort","$3","$_") && next;
/^access-list\s+(\d\d\d)\s+(\S+)\s+ip\s+any/ &&
ProcessHistory("EACL $1 $2","ipsort","0.0.0.0","$_") && next;
# order arp lists
/^arp\s+(\d+\.\d+\.\d+\.\d+)\s+/ &&
ProcessHistory("ARP","ipsort","$1","$_") && next;
/^ip prefix-list\s+(\S+)\s+seq\s+(\d+)\s+(permit|deny)\s+(\d\S+)(\/.*)$/ &&
ProcessHistory("PACL $1 $3","ipsort","$4","ip prefix-list $1 $3 $4$5\n")
&& next;
# order logging statements
/^logging (\d+\.\d+\.\d+\.\d+)/ &&
ProcessHistory("LOGGING","ipsort","$1","$_") && next;
# order/prune snmp-server host statements
# we only prune lines of the form
# snmp-server host a.b.c.d <community>
if (/^snmp-server host (\d+\.\d+\.\d+\.\d+) /) {
if (defined($ENV{'NOCOMMSTR'})) {
my($ip) = $1;
my($line) = "snmp-server host $ip";
my(@tokens) = split(' ', $');
my($token);
while ($token = shift(@tokens)) {
if ($token eq 'version') {
$line .= " " . join(' ', ($token, shift(@tokens)));
} elsif ($token =~ /^(informs?|traps?|(no)?auth)$/) {
$line .= " " . $token;
} else {
$line = "!$line " . join(' ', ("<removed>", join(' ', at tokens)));
last;
}
}
ProcessHistory("SNMPSERVERHOST","ipsort","$ip","$line\n");
} else {
ProcessHistory("SNMPSERVERHOST","ipsort","$1","$_");
}
next;
}
if (/^(snmp-server community) (\S+)/) {
if (defined($ENV{'NOCOMMSTR'})) {
ProcessHistory("SNMPSERVERCOMM","keysort","$_","!$1 <removed>$'") && next;
} else {
ProcessHistory("SNMPSERVERCOMM","keysort","$_","$_") && next;
}
}
# prune tacacs/radius server keys
if (/^(tacacs-server|radius-server) key / && $filter_pwds >= 1) {
ProcessHistory("","","","!$1 key <removed>\n"); next;
}
if (/^((tacacs-server|radius-server) host \S+ key) / &&
$filter_pwds >= 1) {
ProcessHistory("","","","!$1 <removed>\n"); next;
}
# order clns host statements
/^clns host \S+ (\S+)/ &&
ProcessHistory("CLNS","keysort","$1","$_") && next;
# order alias statements
/^alias / && ProcessHistory("ALIAS","keysort","$_","$_") && next;
# delete ntp auth password - this md5 is a reversable too
if (/^(ntp authentication-key \d+ md5) / && $filter_pwds >= 1) {
ProcessHistory("","","","!$1 <removed>\n"); next;
}
# order ntp peers/servers
if (/^ntp (server|peer) (\d+)\.(\d+)\.(\d+)\.(\d+)/) {
$sortkey = sprintf("$1 %03d%03d%03d%03d",$2,$3,$4,$5);
ProcessHistory("NTP","keysort",$sortkey,"$_");
next;
}
# order ip host statements
/^ip host (\S+) / &&
ProcessHistory("IPHOST","keysort","$1","$_") && next;
# order ip nat source static statements
/^ip nat (\S+) source static (\S+)/ &&
ProcessHistory("IP NAT $1","ipsort","$2","$_") && next;
# order atm map-list statements
/^\s+ip\s+(\d+\.\d+\.\d+\.\d+)\s+atm-vc/ &&
ProcessHistory("ATM map-list","ipsort","$1","$_") && next;
# order ip rcmd lines
/^ip rcmd/ && ProcessHistory("RCMD","keysort","$_","$_") && next;
# system controller
/^syscon address (\S*) (\S*)/ &&
ProcessHistory("","","","!syscon address $1 <removed>\n") &&
next;
if (/^syscon password (\S*)/ && $filter_pwds >= 1) {
ProcessHistory("","","","!syscon password <removed>\n");
next;
}
# catch anything that wasnt matched above.
ProcessHistory("","","","$_");
# end of config. the ": " game is for the PIX
if (/^(: +)?end$/) {
$found_end = 1;
return(1);
}
}
# The ContentEngine lacks a definitive "end of config" marker. If we
# know that it is a CE and we have seen at least 5 lines of write term
# o/p, we can be reasonably sure that we got the config.
if ($type =~ /^CE$/ && $linecnt > 5) {
$found_end = 1;
return(1);
}
return(0);
}
# dummy function
sub DoNothing {print STDOUT;}
# Main
%commands=(
'show version' => "ShowVersion",
'show redundancy secondary' => "ShowRedundancy",
'show idprom backplane', => "ShowIDprom",
'show install active' => "ShowInstallActive",
'show env all' => "ShowEnv",
'show rsp chassis-info',=> "ShowRSP",
'show gsr chassis' => "ShowGSR",
'show boot' => "ShowBoot",
'show bootvar' => "ShowBoot",
'show variables boot' => "ShowBoot",
'show flash' => "ShowFlash",
'dir /all nvram:' => "DirSlotN",
'dir /all bootflash:' => "DirSlotN",
'dir /all slot0:' => "DirSlotN",
'dir /all disk0:' => "DirSlotN",
'dir /all slot1:' => "DirSlotN",
'dir /all disk1:' => "DirSlotN",
'dir /all slot2:' => "DirSlotN",
'dir /all disk2:' => "DirSlotN",
"dir /all sup-bootflash:"=> "DirSlotN", # cat 6500-ios
"dir /all sup-microcode:"=> "DirSlotN", # cat 6500-ios
'dir /all slavenvram:' => "DirSlotN",
'dir /all slavebootflash:' => "DirSlotN",
'dir /all slaveslot0:' => "DirSlotN",
'dir /all slavedisk0:' => "DirSlotN",
'dir /all slaveslot1:' => "DirSlotN",
'dir /all slavedisk1:' => "DirSlotN",
'dir /all slaveslot2:' => "DirSlotN",
'dir /all slavedisk2:' => "DirSlotN",
"dir /all slavesup-bootflash:"=> "DirSlotN", # cat 7609
'dir /all sec-nvram:' => "DirSlotN",
'dir /all sec-bootflash:' => "DirSlotN",
'dir /all sec-slot0:' => "DirSlotN",
'dir /all sec-disk0:' => "DirSlotN",
'dir /all sec-slot1:' => "DirSlotN",
'dir /all sec-disk1:' => "DirSlotN",
'dir /all sec-slot2:' => "DirSlotN",
'dir /all sec-disk2:' => "DirSlotN",
'show controllers' => "ShowContAll",
'show controllers cbus' => "ShowContCbus",
'show diagbus' => "ShowDiagbus",
'show diag' => "ShowDiag",
'show module' => "ShowModule", # cat 6500-ios
'show spe version' => "ShowSpeVersion",
'show c7200' => "ShowC7200",
'show vtp status' => "ShowVTP",
'show vlan' => "ShowVLAN",
'show running-config' => "WriteTerm",
'write term' => "WriteTerm"
);
# keys() doesnt return things in the order entered and the order of the
# cmds is important (show version first and write term last). pita
@commands=(
"show version",
"show redundancy secondary",
"show idprom backplane",
"show install active",
"show env all",
"show rsp chassis-info",
"show gsr chassis",
"show boot",
"show bootvar",
"show variables boot",
"show flash",
"dir /all nvram:",
"dir /all bootflash:",
"dir /all slot0:",
"dir /all disk0:",
"dir /all slot1:",
"dir /all disk1:",
"dir /all slot2:",
"dir /all disk2:",
"dir /all sup-bootflash:",
"dir /all sup-microcode:",
"dir /all slavenvram:",
"dir /all slavebootflash:",
"dir /all slaveslot0:",
"dir /all slavedisk0:",
"dir /all slaveslot1:",
"dir /all slavedisk1:",
"dir /all slaveslot2:",
"dir /all slavedisk2:",
"dir /all slavesup-bootflash:",
"dir /all sec-nvram:",
"dir /all sec-bootflash:",
"dir /all sec-slot0:",
"dir /all sec-disk0:",
"dir /all sec-slot1:",
"dir /all sec-disk1:",
"dir /all sec-slot2:",
"dir /all sec-disk2:",
"show controllers",
"show controllers cbus",
"show diagbus",
"show diag",
"show module",
"show spe version",
"show c7200",
"show vtp status",
"show vlan",
"show running-config",
"write term"
);
$cisco_cmds=join(";", at commands);
$cmds_regexp=join("|", at commands);
open(OUTPUT,">$host.new") || die "Can't open $host.new for writing: $!\n";
select(OUTPUT);
# make OUTPUT unbuffered if debugging
if ($debug) { $| = 1; }
if ($file) {
print STDERR "opening file $host\n" if ($debug);
print STDOUT "opening file $host\n" if ($log);
open(INPUT,"<$host") || die "open failed for $host: $!\n";
} else {
print STDERR "executing clogin -t $timeo -c\"$cisco_cmds\" $host\n" if ($debug);
print STDOUT "executing clogin -t $timeo -c\"$cisco_cmds\" $host\n" if ($log);
if (defined($ENV{NOPIPE})) {
system "clogin -t $timeo -c \"$cisco_cmds\" $host </dev/null > $host.raw 2>&1" || die "clogin failed for $host: $!\n";
open(INPUT, "< $host.raw") || die "clogin failed for $host: $!\n";
} else {
open(INPUT,"clogin -t $timeo -c \"$cisco_cmds\" $host </dev/null |") || die "clogin failed for $host: $!\n";
}
}
# determine password filtering mode
if ($ENV{"FILTER_PWDS"} =~ /no/i) {
$filter_pwds = 0;
} elsif ($ENV{"FILTER_PWDS"} =~ /all/i) {
$filter_pwds = 2;
} else {
$filter_pwds = 1;
}
ProcessHistory("","","","!RANCID-CONTENT-TYPE: cisco\n!\n");
ProcessHistory("COMMENTS","keysort","B0","!\n");
ProcessHistory("COMMENTS","keysort","F0","!\n");
ProcessHistory("COMMENTS","keysort","G0","!\n");
TOP: while(<INPUT>) {
tr/\015//d;
if (/[>#]\s?exit$/) {
$clean_run=1;
last;
}
if (/^Error:/) {
print STDOUT ("$host clogin error: $_");
print STDERR ("$host clogin error: $_") if ($debug);
$clean_run=0;
last;
}
while (/#\s*($cmds_regexp)\s*$/) {
$cmd = $1;
if (!defined($prompt)) {
$prompt = ($_ =~ /^([^#]+#)/)[0];
$prompt =~ s/([][}{)(\\])/\\$1/g;
print STDERR ("PROMPT MATCH: $prompt\n") if ($debug);
}
print STDERR ("HIT COMMAND:$_") if ($debug);
if (! defined($commands{$cmd})) {
print STDERR "$host: found unexpected command - \"$cmd\"\n";
$clean_run = 0;
last TOP;
}
$rval = &{$commands{$cmd}};
delete($commands{$cmd});
if ($rval == -1) {
$clean_run = 0;
last TOP;
}
}
}
print STDOUT "Done $logincmd: $_\n" if ($log);
# Flush History
ProcessHistory("","","","");
# Cleanup
close(INPUT);
close(OUTPUT);
if (defined($ENV{NOPIPE})) {
unlink("$host.raw") if (! $debug);
}
# check for completeness
if (scalar(%commands) || !$clean_run || !$found_end) {
if (scalar(%commands)) {
printf(STDOUT "$host: missed cmd(s): %s\n", join(',', keys(%commands)));
printf(STDERR "$host: missed cmd(s): %s\n", join(',', keys(%commands))) if ($debug);
}
if (!$clean_run || !$found_end) {
print STDOUT "$host: End of run not found\n";
print STDERR "$host: End of run not found\n" if ($debug);
system("/usr/bin/tail -1 $host.new");
}
unlink "$host.new" if (! $debug);
}
More information about the Rancid-discuss
mailing list