jerancid failing on asterix's ?

[Mark Cooper]

Think I'm having problems with asterix's being returned in the 'show
environment all' command output ...



lab-srv-001:/var/lib/rancid/bin# cat jerancid.debug
executing clogin -t 90 -c"show version;show redundancy;show boot;show
environment all;dir;show hardware;show configuration" lab-bas-002
PROMPT MATCH: lab-bas-002#
HIT COMMAND:lab-bas-002#show version
    In ShowVersion: lab-bas-002#show version
HIT COMMAND:lab-bas-002#show redundancy
    In ShowRedundancy: lab-bas-002#show redundancy
HIT COMMAND:lab-bas-002#show boot
    In ShowBoot: lab-bas-002#show boot
HIT COMMAND:lab-bas-002#show environment all
    In ShowEnv: lab-bas-002#show environment all
write(spawn_id=1): broken pipe
    while executing
"send_user -- "$expect_out(buffer)""
    invoked from within
"expect -nobrace -re+ { exp_continue } -re {^[^
 *]*lab-bas-002([^#>\r\n]+)?[#>](\([^)\r\n]+\))?} { send_user --
"$expect_out(buffer)"
                                                } -re {..."
    invoked from within
"expect {
                -re "\b+"                       { exp_continue }
                -re "^\[^\n\r *]*$reprompt"     { send_user --
"$expect_out(buffer)"
                                                }
                -re "^\[^\n\r]*$reprompt."      { send..."
    invoked from within
"if [ string match "*\;*" "$command" ] {
        set commands [split $command \;]
        set num_commands [llength $commands]
        # the pager can not be turned off on ..."
    (procedure "run_commands" line 34)
    invoked from within
"run_commands $prompt $command"
    ("foreach" body line 144)
    invoked from within
"foreach router [lrange $argv $i end] {
    set router [string tolower $router]
    send_user "$router\n"

    # Figure out prompt.
    # Since autoena..."
    (file "/var/lib/rancid/bin/clogin" line 616)
lab-bas-002: missed cmd(s): show configuration,show hardware,dir
lab-bas-002: missed cmd(s): show configuration,show hardware,dir
lab-bas-002: End of run not found
lab-bas-002: End of run not found
! *** srp redundancy: mode is high-availability, state disabled
rancid at lab-srv-001:~$ clogin lab-bas-002
lab-bas-002
spawn telnet lab-bas-002
Trying 10.240.8.3...
Connected to lab-bas-002-mgt-lo0.
Escape character is '^]'.


Telnet password: *********
sLogged in on vty 1 via telnet.
Copyright (c) 1999-2005 Juniper Networks, Inc.  All rights reserved.

lab-bas-002>enable
Password: *********
lab-bas-002#
lab-bas-002#show environment all
    chassis: 14 slot (id 0x5, rev. 0xa)
    fabric: 40 Gbps (rev. 0)
    fans: fanSubsystemOk
*** nvs: near capacity (87%), matches running config
    power: A ok, B ok
*** srp redundancy: mode is high-availability, state disabled
        auto-sync enabled, switch-on-error enabled
        status unknown
*** slots: cards missing or offline
        online: 0 1 2 3 4 6 9 10 11 12
        standby: 8
        offline: 7
        empty: 5 13
    line redundancy: 1 redundancy group(s)
        width 6, spare 8, primary 9 10 11 12
    temperature: ok
    timing: primary
        primary: internal SC oscillator (ok)
        secondary: internal SC oscillator (ok)
        tertiary: internal SC oscillator (ok)
        auto-upgrade enabled

*** system operational: no

        processor     processor        IOA           IOA
       temperature   temperature   temperature   temperature
slot   (10C - 70C)     status      (10C - 70C)     status
----   -----------   -----------   -----------   -----------
0          32        normal            ---       unknown
1          32        normal            23        normal
2          34        normal            24        normal
3          32        normal            22        normal
4          36        normal            23        normal
6          30        normal            25        normal
8          33        normal            ---       unknown
9          34        normal            22        normal
10         35        normal            22        normal
11         36        normal            23        normal
12         36        normal            23        normal

processor temperature ranges
        below -5C is too cold
        above 80C is too hot
        low temperature warning below 10C
        high temperature warning above 70C
IOA temperature ranges
        below -5C is too cold
        above 80C is too hot
        low temperature warning below 10C
        high temperature warning above 70C
lab-bas-002#