[rancid] Re: [update]Problem gathering data from an updated ERX junose

[Sven Juergensen (KielNET)]

hi again,

after putting clogin into the $PATH and
redoing the /rancid -d <router> results
in

[...]
HIT COMMAND:<router>#write term
<router>: found unexpected command - "write term"
<router>: End of run not found
<router>: End of run not found

this command doesn't exist on the new
junose release or the previous one.

getting closer but not by much.

thanks for any input.

sven03


Sven Juergensen (KielNET) wrote:
> hi list,
> 
> i'm experiencing issues with collecting
> data from a juniper erx. the device was
> updated from 5.x to 8.x the day before.
> 
> logs result the following:
> 
> ---8<---
> Trying to get all of the configs.
> <router>: missed cmd(s): show configuration,show hardware,dir
> <router>: End of run not found
> ! srp redundancy: mode is high-availability, state active
> =====================================
> --->8---
> 
> this happens four times and then it
> gives up.
> 
> according to the troubleshooting-help in
> your faq under 3) General, first question,
> i can successfully complete the steps of
> 
> 1) ./clogin <router>
> 2) ./clogin -c 'show configuration' <router>
> 
> 3) however does the following:
> 
> ---8<---
> ./rancid <router>
> sh: clogin: command not found
> <router>: missed cmd(s): dir /all slavedisk2:,show rsp chassis-info,dir
> /all sec-slot2:,show diag,dir /all disk1:,show gsr chassis,dir /all
> sec-nvram:,dir /all disk2:,dir /all sec-bootflash:,show spe version,dir
> /all slaveslot2:,dir /all disk0:,show install active,show bootvar,dir
> /all slaveslot0:,dir /all sec-slot1:,dir /all harddiska:,dir /all
> slavenvram:,show flash,dir /all sec-disk2:,dir /all
> slavesup-bootflash:,dir /all sec-disk0:,dir /all harddiskb:,show
> variables boot,show boot,dir /all slavedisk1:,show env all,show
> module,show controllers,show diagbus,dir /all slavedisk0:,show idprom
> backplane,dir /all bootflash:,dir /all sec-slot0:,dir /all
> sec-disk1:,write term,show vtp status,dir /all sup-bootflash:,dir /all
> slot2:,dir /all harddisk:,dir /all slot0:,dir /all sup-microcode:,show
> vlan,dir /all slavebootflash:,show controllers cbus,dir /all
> slaveslot1:,dir /all nvram:,show version,show redundancy secondary,show
> running-config,show c7200,dir /all slot1:
> <router>: End of run not found
> !
> --->8---
> 
> lacking a router.new file, adding a
> '-d' results in:
> 
> ---8<---
> ./rancid -d <router>
> executing clogin -t 90 -c"show version;show redundancy secondary;show
> idprom backplane;show install active;show env all;show rsp
> chassis-info;show gsr chassis;show boot;show bootvar;show variables
> boot;show flash;dir /all nvram:;dir /all bootflash:;dir /all slot0:;dir
> /all disk0:;dir /all slot1:;dir /all disk1:;dir /all slot2:;dir /all
> disk2:;dir /all harddisk:;dir /all harddiska:;dir /all harddiskb:;dir
> /all sup-bootflash:;dir /all sup-microcode:;dir /all slavenvram:;dir
> /all slavebootflash:;dir /all slaveslot0:;dir /all slavedisk0:;dir /all
> slaveslot1:;dir /all slavedisk1:;dir /all slaveslot2:;dir /all
> slavedisk2:;dir /all slavesup-bootflash:;dir /all sec-nvram:;dir /all
> sec-bootflash:;dir /all sec-slot0:;dir /all sec-disk0:;dir /all
> sec-slot1:;dir /all sec-disk1:;dir /all sec-slot2:;dir /all
> sec-disk2:;show controllers;show controllers cbus;show diagbus;show
> diag;show module;show spe version;show c7200;show vtp status;show
> vlan;show running-config;write term" <router>
> sh: clogin: command not found
> <router>: missed cmd(s): dir /all slavedisk2:,show rsp chassis-info,dir
> /all sec-slot2:,show diag,dir /all disk1:,show gsr chassis,dir /all
> sec-nvram:,dir /all disk2:,dir /all sec-bootflash:,show spe version,dir
> /all slaveslot2:,dir /all disk0:,show install active,show bootvar,dir
> /all slaveslot0:,dir /all sec-slot1:,dir /all harddiska:,dir /all
> slavenvram:,show flash,dir /all sec-disk2:,dir /all
> slavesup-bootflash:,dir /all sec-disk0:,dir /all harddiskb:,show
> variables boot,show boot,dir /all slavedisk1:,show env all,show
> module,show controllers,show diagbus,dir /all slavedisk0:,show idprom
> backplane,dir /all bootflash:,dir /all sec-slot0:,dir /all
> sec-disk1:,write term,show vtp status,dir /all sup-bootflash:,dir /all
> slot2:,dir /all harddisk:,dir /all slot0:,dir /all sup-microcode:,show
> vlan,dir /all slavebootflash:,show controllers cbus,dir /all
> slaveslot1:,dir /all nvram:,show version,show redundancy secondary,show
> running-config,show c7200,dir /all slot1:
> <router>: missed cmd(s): dir /all slavedisk2:,show rsp chassis-info,dir
> /all sec-slot2:,show diag,dir /all disk1:,show gsr chassis,dir /all
> sec-nvram:,dir /all disk2:,dir /all sec-bootflash:,show spe version,dir
> /all slaveslot2:,dir /all disk0:,show install active,show bootvar,dir
> /all slaveslot0:,dir /all sec-slot1:,dir /all harddiska:,dir /all
> slavenvram:,show flash,dir /all sec-disk2:,dir /all
> slavesup-bootflash:,dir /all sec-disk0:,dir /all harddiskb:,show
> variables boot,show boot,dir /all slavedisk1:,show env all,show
> module,show controllers,show diagbus,dir /all slavedisk0:,show idprom
> backplane,dir /all bootflash:,dir /all sec-slot0:,dir /all
> sec-disk1:,write term,show vtp status,dir /all sup-bootflash:,dir /all
> slot2:,dir /all harddisk:,dir /all slot0:,dir /all sup-microcode:,show
> vlan,dir /all slavebootflash:,show controllers cbus,dir /all
> slaveslot1:,dir /all nvram:,show version,show redundancy secondary,show
> running-config,show c7200,dir /all slot1:
> <router>: End of run not found
> <router>: End of run not found
> !
> 
> 
> # cat router.new
> !RANCID-CONTENT-TYPE: cisco
> !
> !
> !
> !
> !
> --->8---
> 
> is this a dialogue with the device at all
> or just some dummyattempt? i'm a bit confused
> to why it says cisco - it's configured as
> 'erx' in the cloginrc.
> 
> any input on this greatly appreciated.
> 
> thanks and best regards,
> 
> sven03
> _______________________________________________
> Rancid-discuss mailing list
> Rancid-discuss at shrubbery.net
> http://www.shrubbery.net/mailman/listinfo.cgi/rancid-discuss