[rancid] Re: Need a little help with Auto Enable

[Srinivasa Raju]

You can try this, this might fix the issue
Edit rancid

On Mon, Dec 8, 2008 at 5:19 AM, Hurgh <hurgh at hurgh.org> wrote:

> Hi all,
>
> I am trying to login to a Cisco router that has AutoEnable setup (enter
> user and pass, and you are enabled).
>
> I have the following in my .clogin file:
>
>
> ---------------------------------------------------------------------------------
> add user 172.30.26.16                   myusername
> add password 172.30.26.16               {mypassword}
> add autoenable 172.30.26.16     1
>
> ---------------------------------------------------------------------------------
>
> The User and Pass have been swapped out, but I have confirmed the ones I am
> using are correct (can manually telnet to the device using the user and pass
> to login correctly).
>
> I have confirmed that the router supplies the correct "Username" and
> "Password" prompts.
>
> The following is the error I get when I run:
>
> rancid 172.30.26.16
>
>
> --------------------------------------------------------------------------------
> ./rancid 172.30.26.16
> write(spawn_id=1): broken pipe
>     while executing
> "send_user -- "$expect_out(buffer)""
>     invoked from within
> "expect -nobrace -re+ { exp_continue } -re {^[^
>  *]*spgvsour01c([^#>\r\n]+)?[#>](\([^)\r\n]+\))?} { send_user --
> "$expect_out(buffer)"
>                                                 } -re {..."
>     invoked from within
> "expect {
>                 -re "\b+"                       { exp_continue }
>                 -re "^\[^\n\r *]*$reprompt"     { send_user --
> "$expect_out(buffer)"
>                                                 }
>                 -re "^\[^\n\r]*$reprompt."      { send..."
>     invoked from within
> "if [ string match "*\;*" "$command" ] {
>         set commands [split $command \;]
>         set num_commands [llength $commands]
>         # the pager can not be turned off on ..."
>     (procedure "run_commands" line 34)
>     invoked from within
> "run_commands $prompt $command"
>     ("foreach" body line 150)
>     invoked from within
> "foreach router [lrange $argv $i end] {
>     set router [string tolower $router]
>     # attempt at platform switching.
>     set platform ""
>     send_user ..."
>     (file "/home/rancid/bin/clogin" line 712)
> 172.30.26.16: missed cmd(s): admin show diag,dir /all slavedisk2:,dir /all
> sec-slot2:,show diag,dir /all disk1:,dir /all sec-nvram:,dir /all disk2:,dir
> /all sec-bootflash:,show spe version,dir /all slaveslot2:,dir /all
> disk0:,dir /all slaveslot0:,dir /all sec-slot1:,dir /all harddiska:,dir /all
> slavenvram:,dir /all sec-disk2:,dir /all slavesup-bootflash:,dir /all
> sec-disk0:,dir /all harddiskb:,show inventory raw,dir /all slavedisk1:,show
> module,show controllers,show diagbus,dir /all slavedisk0:,show debug,dir
> /all bootflash:,dir /all sec-slot0:,dir /all sec-disk1:,write term,show vtp
> status,dir /all sup-bootflash:,dir /all slot2:,dir /all harddisk:,dir /all
> slot0:,dir /all sup-microcode:,show vlan,dir /all slavebootflash:,show
> controllers cbus,dir /all slaveslot1:,show vlan-switch,show
> running-config,show c7200,dir /all slot1:
> 172.30.26.16: End of run not found
> !
>
> --------------------------------------------------------------------------------
>
> I have done some searching etc, but can not find what the problem may be.
>
> From reading through the errors, it seems that it is not able to enter the
> user or password, but I dont know why.
>
> Here is the output from a manual telnet to the device:
>
>
> --------------------------------------------------------------------------------
> telnet 172.30.26.16
> Trying 172.30.26.16...
> Connected to 172.30.26.16 (172.30.26.16).
> Escape character is '^]'.
>
>     ***********************************************************************
>     * Access to this computer system is limited to authorised users only. *
>     * Unauthorised users may be subject to prosecution under the Crimes   *
>     *                       Act or State legislation                      *
>     *                                                                     *
>     *   Please note, ALL CUSTOMER DETAILS are confidential and must       *
>     *                          not be disclosed.                          *
>     ***********************************************************************
>
>
>
>
> User Access Verification (ISP V1)
>
> Username: myusername
> Password:
> Signon successful.
>
> spgvsour01c28#
>
> --------------------------------------------------------------------------------
>
> Again, username has been modified for privacy.
>
> If anyone can shed some light on what the issue may be, or point me in a
> direction that may enable me to trouble shoot a bit more, that would be much
> appreciated.
>
> Regards
>
> -Hurgh-
>
> _______________________________________________
> Rancid-discuss mailing list
> Rancid-discuss at shrubbery.net
> http://www.shrubbery.net/mailman/listinfo.cgi/rancid-discuss
>



-- 
"Every man should get married some time; after all, happiness is not the
only thing in life!!"
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://www.shrubbery.net/pipermail/rancid-discuss/attachments/20081208/763e8c3c/attachment.html