[rancid] Re: Issues with cat5

[john heasley]

Fri, Jan 30, 2009 at 06:13:26PM +0000, Ryan DeBerry:
> Yep, it works on a8.  I just downgraded and all is good.

grumble.  There isnt enough info here to determine what the problem is.
Could someone set NOPIPE=YES in your environment and run cat5rancid from
a9 with -d to produce a hostname.raw file.  that should provide some
indication of where the failure is.

> On Fri, Jan 30, 2009 at 5:06 PM, Michael Stefaniuc <mstefani at redhat.com>wrote:
> 
> > Sreekanth K wrote:
> > > Me too have the same problem... I am on  2.3.2a9... Can someone help!!!
> > I'm still on a8 and it works there. It was fixed in a5 or a6 time frame
> > when the two patches went in. I might upgrade to a9 but I'm pretty busy
> > at the moment and don't have time for that.
> >
> > bye
> >         michael
> >
> > > On Thu, Jan 29, 2009 at 7:42 PM, Ryan DeBerry <rdeberry at gmail.com>
> > wrote:
> > >
> > >> Yes, I am using cat5 as the device type.  I can run clogin and it works
> > >> fine.  rancid-run produces the following log.
> > >>
> > >> missed cmd(s): write term all,show port ifindex,show module,dir
> > >> sup-microcode:,dir sup-bootflash:,dir bootflash:,dir slot0:,show
> > >> version,show flash,show running-config,write term,show boot,dir
> > slot1:,show
> > >> inventory raw
> > >> : End of run not found
> > >>
> > >>
> > >> Below is a link to old thread.
> > >>
> > >> http://osdir.com/ml/network.rancid/2008-06/msg00018.html
> > >>
> > >>
> > >> On Thu, Jan 29, 2009 at 1:05 PM, Michael Stefaniuc <mstefani at redhat.com
> > >wrote:
> > >>
> > >>> Ryan DeBerry wrote:
> > >>>> I have seen many posts in the archives with the same issue but I have
> > >>> not
> > >>>> seen a resolution.
> > >>> Which rancid version are you using? I have submitted patches to fix the
> > >>> problem and those were accepted (in a modified) form upstream. I use
> > >>> rancid-2.3.2a8 and the only CatOS specific patch I have is to kill the
> > >>> bogus "set portcost" config lines.
> > >>>
> > >>>> clogin works just fine but rancid-run spits out error timeout reached
> > >>> Btw. what device type are you using for the CatOS devices: "cisco" or
> > >>> "cat5"? "cat5" is the correct type.
> >
> >
> >
> > --
> > Michael Stefaniuc                           Tel.: +49-711-96437-199
> > Consulting Communications Engineer          Fax.: +49-711-96437-111
> > --------------------------------------------------------------------
> > Reg. Adresse: Red Hat GmbH, Otto-Hahn-Strasse 20, 85609 Dornach bei
> > Muenchen
> > Handelsregister: Amtsgericht Muenchen HRB 153243
> > Gesch?ftsf?hrer: Brendan Lane, Charlie Peters, Michael Cunningham,
> >                 Werner Knoblich
> >

> _______________________________________________
> Rancid-discuss mailing list
> Rancid-discuss at shrubbery.net
> http://www.shrubbery.net/mailman/listinfo.cgi/rancid-discuss