[rancid] Cisco FWSM Upgrade - Broke rancid; Need your Advice ...

[Lee]

That
  clogin: not found
looks like a problem, but to answer your question about knowing which
command failed
set NOPIPE=YES in your environment and run rancid -d hostname.  look
in hostname.raw for the commands and their output.

Regards,
Lee


On 8/18/13, Wilkinson, Alex <alex.wilkinson at cba.com.au> wrote:
> Hi all,
>
> After an FWSM OS upgrade (to 3.2(26)) rancid is now broke for our FWSM(s)
> e.g.
>
>     Trying to get all of the configs.
>     fwsmfw: missed cmd(s): write term
>     fwsmfw: End of run not found
>     Error: TIMEOUT reached
>
> Running rancid in debug mode gives me:
>
> $ /usr/local/libexec/rancid/rancid -d fwsmfw
> executing clogin -t 90 -c"show version;show redundancy secondary;show idprom
> backplane;show install active;show env all;show rsp chassis-info;show gsr
> chassis;show diag chassis-info;show boot;show bootvar;show variables
> boot;show flash;dir /all nvram:;dir /all bootflash:;dir /all slot0:;dir /all
> disk0:;dir /all slot1:;dir /all disk1:;dir /all slot2:;dir /all disk2:;dir
> /all harddisk:;dir /all harddiska:;dir /all harddiskb:;dir /all
> sup-bootdisk:;dir /all sup-bootflash:;dir /all sup-microcode:;dir /all
> slavenvram:;dir /all slavebootflash:;dir /all slaveslot0:;dir /all
> slavedisk0:;dir /all slaveslot1:;dir /all slavedisk1:;dir /all
> slaveslot2:;dir /all slavedisk2:;dir /all slavesup-bootflash:;dir /all
> sec-nvram:;dir /all sec-bootflash:;dir /all sec-slot0:;dir /all
> sec-disk0:;dir /all sec-slot1:;dir /all sec-disk1:;dir /all sec-slot2:;dir
> /all sec-disk2:;show controllers;show controllers cbus;show diagbus;show
> diag;show capture;show module;show spe version;show c7200;show inventory
> raw;s
>  how vtp status;show vlan;show vlan-switch;show debug;show shun;more
> system:running-config;show running-config view full;show
> running-config;write term" fwsmfw
> clogin: not found
> fwsmfw: missed cmd(s): dir /all slavedisk2:,show rsp chassis-info,show
> capture,dir /all sec-slot2:,show diag,dir /all disk1:,show gsr chassis,dir
> /all sec-nvram:,show diag chassis-info,dir /all disk2:,show running-config
> view full,dir /all sec-bootflash:,show spe version,dir /all slaveslot2:,dir
> /all disk0:,show install active,show bootvar,dir /all slaveslot0:,dir /all
> sec-slot1:,dir /all harddiska:,dir /all slavenvram:,show flash,dir /all
> sec-disk2:,dir /all slavesup-bootflash:,dir /all sec-disk0:,dir /all
> harddiskb:,show variables boot,show boot,show inventory raw,dir /all
> slavedisk1:,show env all,show module,show shun,show controllers,show
> diagbus,more system:running-config,dir /all slavedisk0:,show debug,show
> idprom backplane,dir /all bootflash:,dir /all sup-bootdisk:,dir /all
> sec-slot0:,dir /all sec-disk1:,write term,show vtp status,dir /all
> sup-bootflash:,dir /all slot2:,dir /all harddisk:,dir /all slot0:,dir /all
> sup-microcode:,show vlan,dir /all slavebootflash:,show controlle
>  rs cbus,dir /all slaveslot1:,dir /all nvram:,show version,show
> vlan-switch,show redundancy secondary,show running-config,show c7200,dir
> /all slot1:
> fwsmfw: missed cmd(s): dir /all slavedisk2:,show rsp chassis-info,show
> capture,dir /all sec-slot2:,show diag,dir /all disk1:,show gsr chassis,dir
> /all sec-nvram:,show diag chassis-info,dir /all disk2:,show running-config
> view full,dir /all sec-bootflash:,show spe version,dir /all slaveslot2:,dir
> /all disk0:,show install active,show bootvar,dir /all slaveslot0:,dir /all
> sec-slot1:,dir /all harddiska:,dir /all slavenvram:,show flash,dir /all
> sec-disk2:,dir /all slavesup-bootflash:,dir /all sec-disk0:,dir /all
> harddiskb:,show variables boot,show boot,show inventory raw,dir /all
> slavedisk1:,show env all,show module,show shun,show controllers,show
> diagbus,more system:running-config,dir /all slavedisk0:,show debug,show
> idprom backplane,dir /all bootflash:,dir /all sup-bootdisk:,dir /all
> sec-slot0:,dir /all sec-disk1:,write term,show vtp status,dir /all
> sup-bootflash:,dir /all slot2:,dir /all harddisk:,dir /all slot0:,dir /all
> sup-microcode:,show vlan,dir /all slavebootflash:,show controlle
>  rs cbus,dir /all slaveslot1:,dir /all nvram:,show version,show
> vlan-switch,show redundancy secondary,show running-config,show c7200,dir
> /all slot1:
> fwsmfw: End of run not found
> fwsmfw: End of run not found
> !
> $
>
> How does one know exactly which of the aforementioned commands failed ? And
> once
> this is known, where does one change (remove) the offending commands ?
>
> Thanks!
>
>    -Alex
>
>
> ************** IMPORTANT MESSAGE *****************************
> This e-mail message is intended only for the addressee(s) and contains
> information which may be
> confidential.
> If you are not the intended recipient please advise the sender by return
> email, do not use or
> disclose the contents, and delete the message and any attachments from your
> system. Unless
> specifically indicated, this email does not constitute formal advice or
> commitment by the sender
> or the Commonwealth Bank of Australia (ABN 48 123 123 124) or its
> subsidiaries.
> We can be contacted through our web site: commbank.com.au.
> If you no longer wish to receive commercial electronic messages from us,
> please reply to this
> e-mail by typing Unsubscribe in the subject line.
> **************************************************************
>
>
>
> _______________________________________________
> Rancid-discuss mailing list
> Rancid-discuss at shrubbery.net
> http://www.shrubbery.net/mailman/listinfo/rancid-discuss
>