[rancid] new rancid install not working

[Jeffrey d'Ambly]

Ok so I got that sorted out
qa-scl009-005:/var/log/rancid# whoami
rancid
qa-scl009-005:/var/log/rancid# which clogin
/usr/libexec/rancid/clogin
qa-scl009-005:/var/log/rancid#

/usr/bin/rancid -d -t cisco sjc-vpe1
Gives me what I think should happen at least. It creates a file
sjc-vpe1.new in the local dir I¹m in.


But when I run /usr/bin/rancid-run I just get what looks like an empty file

qa-scl009-005:/var/rancid/routers/configs# cat sjc-core01.new
!RANCID-CONTENT-TYPE: cisco
!
!
!
!
!




‹jeff



On 4/17/15, 3:43 PM, "heasley" <heas at shrubbery.net> wrote:

>Fri, Apr 17, 2015 at 10:41:54PM +0000, Jeffrey d'Ambly:
>> I cannot for the life of me figure out what I¹m doing wrong here.
>> 
>> When I run /usr/bin/rancid-run it seems like nothing happens. When I
>>run rancid manually I get the following
>> 
>> 
>> qa-scl009-005:/var/rancid# /usr/bin/rancid -d -t cisco sjc-vpe1
>> 
>> loadtype: device type cisco
>> 
>> loadtype: found device type cisco in /etc/rancid/rancid.types.base
>> 
>> executing clogin -t 90 -c"show version;show redundancy;show idprom
>>backplane;show install active;show env all;show rsp chassis-info;show
>>gsr chassis;show diag chassis-info;show boot;show bootvar;show variables
>>boot;show flash;dir /all nvram:;dir /all bootflash:;dir /all slot0:;dir
>>/all disk0:;dir /all slot1:;dir /all disk1:;dir /all slot2:;dir /all
>>disk2:;dir /all harddisk:;dir /all harddiska:;dir /all harddiskb:;dir
>>/all sup-bootdisk:;dir /all sup-bootflash:;dir /all sup-microcode:;dir
>>/all slavenvram:;dir /all slavebootflash:;dir /all slaveslot0:;dir /all
>>slavedisk0:;dir /all slaveslot1:;dir /all slavedisk1:;dir /all
>>slaveslot2:;dir /all slavedisk2:;dir /all slavesup-bootflash:;dir /all
>>sec-nvram:;dir /all sec-bootflash:;dir /all sec-slot0:;dir /all
>>sec-disk0:;dir /all sec-slot1:;dir /all sec-disk1:;dir /all
>>sec-slot2:;dir /all sec-disk2:;show controllers;show controllers
>>cbus;show diagbus;show diag;show capture;show module;show spe
>>version;show c7200;show inventory raw;show vtp status;show vlan;show
>>vlan-switch;show switch detail;show sdm prefer;show system mtu;show
>>debug;show shun;more system:running-config;show running-config view
>>full;show running-config;write term" sjc-vpe1
>> 
>> sh: clogin: command not found
>
>set your PATH correctly
>
>> sjc-vpe1: missed cmd(s): all commands
>> 
>> sjc-vpe1: End of run not found
>> 
>> sjc-vpe1: End of run not found
>> 
>> But if I can clogin manually it works
>> 
>> 
>> qa-scl009-005:/var/log/rancid# /usr/libexec/rancid/clogin -t 90 -c"show
>>version" sjc-vpe1
>> 
>> sjc-vpe1
>> 
>> spawn ssh -c 3des -x -l confbackup sjc-vpe1
>> 
>> Password:
>> 
>> sjc-vpe1#
>> 
>> sjc-vpe1#terminal length 0
>> 
>> sjc-vpe1#terminal width 132
>> 
>> sjc-vpe1#show version
>> 
>> Cisco IOS Software, C3900e Software (C3900e-UNIVERSALK9-M), Version
>>15.2(4)M7, RELEASE SOFTWARE (fc2)
>> 
>> Technical Support: http://www.cisco.com/techsupport
>> 
>> Copyright (c) 1986-2014 by Cisco Systems, Inc.
>> 
>> Compiled Thu 25-Sep-14 10:09 by prod_rel_team
>> 
>> 
>> ROM: System Bootstrap, Version 15.1(1r)T5, RELEASE SOFTWARE (fc1)
>> 
>> I have no idea what the hell I am doing wrong here, if someone could
>>point me in the right direction here that would be awesome.
>> 
>> ‹Jeff
>
>> _______________________________________________
>> Rancid-discuss mailing list
>> Rancid-discuss at shrubbery.net
>> http://www.shrubbery.net/mailman/listinfo/rancid-discuss
>