[rancid] New device type
Rod Hendricks
rod.hendricks at graduate.uwa.edu.au
Thu Dec 17 08:06:13 UTC 2015
Thanks for the help Alan.
My perl module is based on the builtin ciscowlc module.
The exit condition (if I've understood you correctly) is this:-
ProcessHistory("","","","\n!--WLC End Config Data--!\n");
print STDERR " Exiting ShowConfig: $_" if ($debug);
# WLC lacks a definitive "end of config" marker.
if ($linecnt > 5) {
$found_end = 1;
return(1);
}
It seems like the perl module is telling me the file is short, but the raw
file is definitely the full show running-config output.
I'm kinda lost now :/
Cheers,
Rod.
On Thu, Dec 17, 2015 at 2:16 PM, Alan McKinnon <alan.mckinnon at gmail.com>
wrote:
> That's a fairly common error, but it never has a common solution.
>
> Basically, your script read the raw file, detected the start of "show
> running-config" and started to process it in sub ShowConfig()
>
> However, the script didn't find the end of that output for whatever
> reason and processing fell all the way through to the very end with the
> error "End of run not found". You will have to dig into the script and
> find what it uses for that. There's a main loop in ShowConfig() and it
> will have a regex exit condition (possibly "end" followed by a prompt or
> something similar).
>
> Carefully examine the raw file to see what your device put out, and make
> ShowConfig() match.
>
>
> On 17/12/2015 08:01, Rod Hendricks wrote:
> > I'm getting closer.
> >
> > rancid.types.conf now looks like this:-
> > hirschmann;script;rancid -t hirschmann
> > hirschmann;login;hmlogin
> > hirschmann;module;hirschmann
> > hirschmann;inloop;hirschmann::inloop
> > hirschmann;command;hirschmann::ShowConfig;show running-config
> >
> > Output now looks like this:-
> > -bash-4.2$ rancid -d -thirschmann 192.168.254.103
> > loadtype: device type hirschmann
> > loadtype: found device type hirschmann in /etc/rancid/rancid.types.conf
> > executing hmlogin -t 90 -c"show running-config" 192.168.254.103
> > PROMPT MATCH:
> > HIT COMMAND:(Hirschmann Railswitch) #show running-config
> > HIT COMMAND:(Hirschmann Railswitch) #show running-config
> > In ShowConfig: (Hirschmann Railswitch) #show running-config
> > Exiting ShowConfig:
> > 192.168.254.103 <http://192.168.254.103>: End of run not found
> > 192.168.254.103 <http://192.168.254.103>: End of run not found
> > !--WLC End Config Data--!
> > -bash-4.2$
> >
> > .raw file still looks correct.
> >
> > .new file looks like:-
> > !RANCID-CONTENT-TYPE: hirschmann
> > !
> >
> > !--WLC Begin Config Data--!
> >
> > !--WLC End Config Data--!
> >
> > Ideas?
> >
> > Cheers,
> > Rod.
> >
> >
> >
> > On Wed, Dec 16, 2015 at 11:57 PM, Dan Anderson <dan.w.anderson at gmail.com
> > <mailto:dan.w.anderson at gmail.com>> wrote:
> >
> > That field is basically a call to a subroutine within the module so
> > if you copied ciscowlc.pm <http://ciscowlc.pm>, you'd need to use
> > ShowConfig as WriteTerm doesn't exist in that module.
> >
> > On Wed, Dec 16, 2015 at 10:26 AM, Rod Hendricks
> > <rod.hendricks at graduate.uwa.edu.au
> > <mailto:rod.hendricks at graduate.uwa.edu.au>> wrote:
> >
> > I don't fully understand the purpose of WriteTerm. But from
> > what you are saying above, is my rancid.types.conf in my
> > original post wrong? Should
> >
> > hirschmann;command;hirschmann::WriteTerm;show running-config
> >
> > in fact look like
> >
> > hirschmann;command;hirschmann::ShowConfig;show running-config
> >
> > ?
> > If so, I guess I've messed that up by not understanding the
> > significance of that keyword. Rancid server is on my work dev
> > box - will try this out in 12hrs when i get back to the office.
> >
> > Thanks again.
> >
> > Cheers,
> > Rod.
> >
> > On Wed, Dec 16, 2015 at 11:07 PM, Dan Anderson
> > <dan.w.anderson at gmail.com <mailto:dan.w.anderson at gmail.com>>
> wrote:
> >
> > ShowConfig in ciscowlc.pm <http://ciscowlc.pm> uses the line
> > counting method.
> >
> > while (<$INPUT>) {
> > <---SNIP--->
> >
> > $linecnt++;
> > <---SNIP--->
> >
> > # WLC lacks a definitive "end of config" marker.
> > if ($linecnt > 5) {
> > $found_end = 1;
> > return(1);
> > }
> > return(0);
> >
> >
> > WriteTerm in ios.pm <http://ios.pm> looks for the "end"
> keyword.
> >
> > On Wed, Dec 16, 2015 at 9:50 AM, Rod Hendricks
> > <rod.hendricks at graduate.uwa.edu.au
> > <mailto:rod.hendricks at graduate.uwa.edu.au>> wrote:
> >
> > Thanks Dan.
> >
> > Your explanation makes sense. Which script normally
> > defines this delimiter? I would be happy to settle for
> > the moment in just short-circuiting this delimiter check
> > so I can I can get the job running. Have included
> > device config below. Don't worry about the passwords -
> > its a test unit with factory default config.
> >
> > Escape character is '^]'.
> >
> >
> >
> > Copyright (c) 2004-2015 Hirschmann Automation
> > and Control GmbH
> >
> > All rights reserved
> >
> > Railswitch Release L2E-08.0.09
> >
> > (Build date 2015-04-06 21:32)
> >
> >
> >
> > System Name: RS-F602F7
> > Mgmt-IP : 192.168.254.103
> > Base-MAC : 00:80:63:F6:02:F7
> > System Time: 2015-01-02 10:11:52
> >
> >
> >
> > (Hirschmann Railswitch)
> > User:admin
> > Password:*******
> >
> > NOTE: Enter '?' for Command Help. Command help displays
> > all options
> > that are valid for the 'normal' command forms of
> > that particular mode.
> > For a list of valid 'no' command forms for that
> > mode, enter the help
> > command 'no ?'. For the syntax of a particular
> > command form, please
> > consult the documentation.
> >
> >
> > (Hirschmann Railswitch) >enable
> >
> > (Hirschmann Railswitch) #
> > (Hirschmann Railswitch) #show running-config
> >
> > !Current Configuration:
> > !
> > !Parameter string escape handling \, 1
> > !Characters to be preceded with escape char (\): \, !,
> > ", ', ?
> >
> > !System Description "Hirschmann Railswitch"
> > !System Version L2E-08.0.09 Build: 2015-04-06 21:32
> >
> > vlan database
> > exit
> >
> >
> > configure
> >
> > !
> >
> >
> > interface 1/1
> > no auto-negotiate
> >
> > exit
> >
> >
> > interface 1/2
> > no auto-negotiate
> >
> > exit
> >
> >
> > interface 1/3
> >
> > exit
> >
> >
> > interface 1/4
> >
> > exit
> >
> >
> > interface 1/5
> >
> > exit
> >
> >
> > interface 1/6
> >
> > exit
> >
> >
> > interface 1/7
> >
> > exit
> >
> >
> > interface 1/8
> >
> > exit
> >
> >
> > !Address Conflict Detection
> >
> > !Bridge Address Learning
> >
> > !Bridge Fast Link Detection
> >
> > !Maximum size of frame (packet size)
> >
> > !Bridge Address Relearn Detection
> >
> > !Bridge Address Relearn Threshold
> >
> > !Bridge Duplex Mismatch Detection
> >
> > !Bridge Hash Optimizing
> >
> > !Service Mode
> >
> > !VLAN Learning
> >
> >
> > !Hirschmann DHCP Relay
> >
> > !Hirschmann Device Status
> >
> >
> > !DIP Switch Admin State
> >
> >
> > !Ethernet/IP
> >
> > !Power over Ethernet (IEEE 802.3af)
> > !Selftest
> >
> > !Skip ACA on boot
> >
> >
> > !Hirschmann HIPER Ring
> > ! configuration determined by DIP switch
> > hiper-ring mode ring-switch
> > hiper-ring port primary 1/1
> > hiper-ring port secondary 1/2
> >
> > !LLDP (IEEE802.1AB Link Layer Discovery Protocol)
> >
> > !Media Redundancy Protocol (IEC 62439-2/Ed1.0, MRP)
> > !No MRP domains exist.
> >
> > !MAC/IP Based Port Security
> >
> >
> > !ProfinetIO
> >
> >
> > !Hirschmann Precision Time Protocol (PTP, IEEE 1588)
> >
> > !Hirschmann Ring Coupling
> > !Note: master/slave (also for single) part of
> > configuration determined by
> > ! DIP switch (cannot be overridden by management)
> > ring-coupling operation on
> >
> > !Hirschmann Signal Contacts
> >
> >
> > !Hirschmann SNMP Access Control
> >
> >
> > !SNTP
> >
> >
> > !Hirschmann Broadcast Limiter
> >
> >
> > !Hirschmann Temperature Limit Settings
> >
> > users passwd admin
> >
> :v1:81449548fb49a99be2d6411bdb9a10ea7e9c92c9510eb373a26176b48b934890:
> > users snmpv3 authentication admin md5
> > users passwd user
> >
> :v1:81439e52f35ecca73b21339156609d20cf630a65d0e92261cb29e58647ae54f4:
> > users snmpv3 authentication user md5
> >
> > lineconfig
> > exit
> >
> > no spanning-tree
> >
> > !IGMP Snooping
> > exit
> >
> >
> > (Hirschmann Railswitch) #logoutConnection closed by
> > foreign host.
> > -bash-4.2$
> >
> > Cheers,
> > Rod.
> >
> > On Wed, Dec 16, 2015 at 10:21 PM, Dan Anderson
> > <dan.w.anderson at gmail.com
> > <mailto:dan.w.anderson at gmail.com>> wrote:
> >
> > It sounds like it's not finding an
> > end-of-configuration delimiter. I'm not familiar
> > with the device type, but for Cisco devices, it
> > usually looks for the keyword "end" by itself at the
> > end of "show run" to determine whether or not it has
> > successfully pulled the configuration. Other device
> > types sometimes look for more than 5 lines of
> > config, etc. Without knowing more about the
> > configuration file format, I can't say which method
> > (if either) would work for your situation.
> >
> > On Wed, Dec 16, 2015 at 5:49 AM, Rod Hendricks
> > <rod.hendricks at graduate.uwa.edu.au
> > <mailto:rod.hendricks at graduate.uwa.edu.au>> wrote:
> >
> > Hi.
> >
> > I am really struggling with getting a new device
> > type up and running.
> >
> > Rancid v3.2, installed into Centos 7 with yum
> > from EPEL repo. I have an installation that is
> > currently working against a test Cisco router,
> > so I know the base install is all good.
> >
> > I have created a login script hmlogin (based off
> > complogin, with session paginate commented out)
> > I have created a perl script hirschmann.pm
> > <http://hirschmann.pm> (based on ciscowlc.om
> > <http://ciscowlc.om>).
> >
> > rancid.types.conf:
> > hirschmann;script;rancid -t hirschmann
> > hirschmann;login;hmlogin
> > hirschmann;module;hirschmann
> > hirschmann;inloop;hirschmann::inloop
> > hirschmann;command;hirschmann::WriteTerm;show
> > running-config
> >
> > I can run it directly with hmlogin -c"show
> > running-config" 192.168.254.103
> > I get no errors running this, and I get the
> > output expected.
> >
> > However, when I run the following: rancid -d
> > -thirschmann 192.168.254.103
> > I get:
> > loadtype: device type hirschmann
> > loadtype: found device type hirschmann in
> > /etc/rancid/rancid.types.conf
> > executing hmlogin -t 90 -c"show running-config"
> > 192.168.254.103
> > PROMPT MATCH:
> > HIT COMMAND:(Hirschmann Railswitch) #show
> > running-config
> > HIT COMMAND:(Hirschmann Railswitch) #show
> > running-config
> > 192.168.254.103 <http://192.168.254.103>: missed
> > cmd(s): all commands
> > 192.168.254.103 <http://192.168.254.103>: End of
> > run not found
> > 192.168.254.103 <http://192.168.254.103>: End of
> > run not found
> > !
> > -bash-4.2$
> >
> > The .raw file has the full correct output of the
> > show running-config.
> > The .new file only has:
> > !RANCID-CONTENT-TYPE: hirschmann
> > !
> >
> > I feel oh so close to getting this running!
> > Appreciate any help that can be offered.
> >
> > Cheers,
> > Rod.
> >
> > _______________________________________________
> > Rancid-discuss mailing list
> > Rancid-discuss at shrubbery.net
> > <mailto:Rancid-discuss at shrubbery.net>
> >
> http://www.shrubbery.net/mailman/listinfo/rancid-discuss
> >
> >
> >
> >
> > --
> > Dan
> >
> >
> >
> > _______________________________________________
> > Rancid-discuss mailing list
> > Rancid-discuss at shrubbery.net
> > <mailto:Rancid-discuss at shrubbery.net>
> > http://www.shrubbery.net/mailman/listinfo/rancid-discuss
> >
> >
> >
> >
> > --
> > Dan
> >
> >
> >
> > _______________________________________________
> > Rancid-discuss mailing list
> > Rancid-discuss at shrubbery.net <mailto:
> Rancid-discuss at shrubbery.net>
> > http://www.shrubbery.net/mailman/listinfo/rancid-discuss
> >
> >
> >
> >
> > --
> > Dan
> >
> >
> >
> >
> > _______________________________________________
> > Rancid-discuss mailing list
> > Rancid-discuss at shrubbery.net
> > http://www.shrubbery.net/mailman/listinfo/rancid-discuss
> >
>
>
> --
> Alan McKinnon
> alan.mckinnon at gmail.com
>
> _______________________________________________
> Rancid-discuss mailing list
> Rancid-discuss at shrubbery.net
> http://www.shrubbery.net/mailman/listinfo/rancid-discuss
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://www.shrubbery.net/pipermail/rancid-discuss/attachments/20151217/7973638a/attachment.html>
More information about the Rancid-discuss
mailing list