Default setting: pcia-probe-list 1

/pci@1f,0/pci@1 is the pcia-probe-list variable. The default is set to 1. If you wish to disable probing the single PCI slot available in the Netra T1 105, simply change the pci-probe-list value from 1 to 0

	Change to: pcia-probe-list 0      

This can be done at the OK prompt using the setenv command.

OK setenv pcia-probe-list 0

Default setting: pcib-probe-list 1,2,3

NOTE - 1,2 was the default on some of the early machines. See SRDB 21974 for more information on enabling the second ethernet port.

The ide and scsi devices use the pcib-probe-list value number 2.

/pci@1f,0/pci@1/pci@1/ide@e
/pci@1f,0/pci@1/pci@1/ide@e/cdrom
/pci@1f,0/pci@1/pci@1/ide@e/disk
/pci@1f,0/pci@1,1/scsi@2
/pci@1f,0/pci@1,1/network@1,1
/pci@1f,0/pci@1,1/ebus@1
/pci@1f,0/pci@1,1/scsi@2/tape
/pci@1f,0/pci@1,1/scsi@2/disk      

The ebus devices use the pcib-probe-list value number 1.

/pci@1f,0/pci@1,1/ebus@1/SUNW,lom@14,400000
/pci@1f,0/pci@1,1/ebus@1/i2c@14,100000
/pci@1f,0/pci@1,1/ebus@1/i2c@14,600000
/pci@1f,0/pci@1,1/ebus@1/flashprom@10,800000
/pci@1f,0/pci@1,1/ebus@1/flashprom@10,400000
/pci@1f,0/pci@1,1/ebus@1/beeper@14,722000
/pci@1f,0/pci@1,1/ebus@1/display7seg@14,200040
/pci@1f,0/pci@1,1/ebus@1/watchdog@14,200000
/pci@1f,0/pci@1,1/ebus@1/flashprom@10,0
/pci@1f,0/pci@1,1/ebus@1/eeprom@14,0
/pci@1f,0/pci@1,1/ebus@1/fdthree@14,3203f0
/pci@1f,0/pci@1,1/ebus@1/ecpp@14,340278
/pci@1f,0/pci@1,1/ebus@1/su@14,3602f8
/pci@1f,0/pci@1,1/ebus@1/su@14,3803f8
/pci@1f,0/pci@1,1/ebus@1/SUNW,pll@14,504000
/pci@1f,0/pci@1,1/ebus@1/power@14,724000
/pci@1f,0/pci@1,1/ebus@1/auxio@14,726000
/pci@1f,0/pci@1,1/ebus@1/i2c@14,600000/gpio@0,72
/pci@1f,0/pci@1,1/ebus@1/i2c@14,600000/gpio@0,70
/pci@1f,0/pci@1,1/ebus@1/i2c@14,600000/adc@0,9e      

The second network interface use the pcib-probe-list value number 3.

/pci@1f,0/pci@1,1/network@3,1