InfoDoc ID   Synopsis   Date
45504   RSC Command Quick Reference Guide   3 Dec 2002

Status Issued

Description

RSC Commands at the rsc> prompt.

environment Displays current environmental information

showenvironment (The showenvironment command is not available on Sun Enterprise[TM] 250 servers.)

shownetwork Displays the current network configuration

console Connects you to the server console

break Puts the server in debug mode

xir Generates an externally initiated reset to the server

bootmode Controls server firmware behavior, if followed by a server reset within 10 minutes (similar to L1-key combinations on Sun keyboards)

reset Resets the server immediately

poweroff Powers off the server

poweron Powers on the server

loghistory Displays the history of all events logged in the RSC event buffer

consolehistory Displays the history of all console messages logged in the buffer

consolerestart Makes the current boot and run console logs "original"

set Sets a configuration variable

serial_baud serial_stop serial_data serial_hw_handshake
ppp_local_ip_addr ppp_remote_ip_addr ppp_enabled page_enabled
mail_enabled page_info1 page_init1 page_password1
page_baud1 page_data1 page_parity1 page_stop1
page_info2 page_init2 page_password2 page_baud2
page_data2 page_parity2 page_stop2 customerinfo
hostname mailuser mailhost ip_mode
ip_addr ip_netmask ip_gateway escape_char
country_code + page_verbose * tpe_link_test

+rsc 2.0 and above

*not available for the 250

show Displays one or more configuration variables

date Displays or sets the current time and date

password Changes your RSC password

useradd Adds an RSC user account

userdel Deletes an RSC user account

usershow Shows characteristics of an RSC user account

userpassword Sets or changes a user's password

userperm Sets the authorization for a user

resetrsc Resets RSC immediately

help Displays a list of RSC shell commands and a brief description of each

version Displays the RSC firmware version

showsc (The showsc command is not available on Sun Enterprise 250 servers.)

logout Ends your current RSC shell session

setlocator Turn the system locator LED on or off (Sun Fire[TM] V480 servers only).

showlocator Show the state of the system locator LED (Sun Fire V480 servers only).

showdate Same as the date command without arguments. (Not available for Sun Enterprise 250 servers.)

setdate Same as the date command with arguments. (Not available for Sun Enterprise 250 servers.)

rscadm subcommands

help Displays a list of rscadm commands and brief descriptions for each

date Displays or sets the current time and date

set Sets a configuration variable

show Displays one or more configuration variables

shownetwork Shows current RSC card network configuration (RSC 2.0 and above)

loghistory Returns the most recent log entries (RSC 2.0 and above)

resetrsc Resets RSC immediately

download Downloads firmware to the RSC flash PROM

send_event Logs an event; can also send an alert message

modem_setup Changes configuration of the modem connected to the RSC serial port

useradd Adds an RSC user account

userdel Deletes an RSC user account

usershow Shows characteristics of an RSC user account

userpassword Sets or changes a user's password

userperm Sets the authorization for a user

version Reports the RSC version on the host (RSC 2.0 and above)

status Same as the version -v command. (RSC 2.0 and above)

OBP Commands

rsc-hard-reset Performs a hard reset of RSC; this is the same as using the command rscadm resetrsc.

rsc-soft-reset Performs a soft reset of RSC; this is the same as using the command rscadm resetrsc -s.

diag-output-to rsc*|rsc-console**|ttya Directs POST output to either RSC (1) or ttya (0). This command takes effect after the next server reset. (E250 only)

diag-console rsc*|rsc-console**|ttya This command directs power-on self-test (POST) output to either RSC (1) or ttya (0). This command takes effect after the next server reset. (Not available for the 250)

rsc-mac-update Updates the RSC Ethernet address from the contents of the server ID PROM. Use this command after replacing the server NVRAM module.

.rsc Displays RSC information, including the diag-output-to setting and the RSC POST status word.

*Available for Sun Enterprise 250 servers only. For other supported workgroup servers, you must set input-device and output-device to rsc-console rather than to rsc.

**For Sun Enterprise 250 servers, you must set input-device and output-device to rsc rather than to rsc-console.

OBP Environment Variable Properties

input-device rsc|rsc!|ttya

output-device rsc|rsc!|ttya

diag-out-console true|false (V480 only)

Keywords: RSC E250 280R V880 V480

INTERNAL SUMMARY:

SUBMITTER: Robert Warfield APPLIES TO: AFO Vertical Team Docs/Hardware ATTACHMENTS:


Copyright (c) 1997-2003 Sun Microsystems, Inc.