[rancid] Re: How do i downgrade from 2.3.2a9 to 2.3.2a8

[Mina Eskander]

I have autoenable set to 0, so rancid has to manually enter the enable password, when I do a clogin <switchname> it logs in and gets into enable mode just fine.
But when I run rancid -d <switchname> I get the following output

[rancid at pwsecLX bin]$ rancid -d <switchname>
executing clogin -t 90 -c"admin show version;show version;show redundancy secondary;show idprom backplane;show install active;admin show env all;show env all;show rsp chassis-info;show gsr chassis;show diag chassis-info;show boot;show bootvar;admin show variables boot;show variables boot;show flash;dir /all nvram:;dir /all bootflash:;dir /all slot0:;dir /all disk0:;dir /all slot1:;dir /all disk1:;dir /all slot2:;dir /all disk2:;dir /all harddisk:;dir /all harddiska:;dir /all harddiskb:;dir /all sup-bootflash:;dir /all sup-microcode:;dir /all slavenvram:;dir /all slavebootflash:;dir /all slaveslot0:;dir /all slavedisk0:;dir /all slaveslot1:;dir /all slavedisk1:;dir /all slaveslot2:;dir /all slavedisk2:;dir /all slavesup-bootflash:;dir /all sec-nvram:;dir /all sec-bootflash:;dir /all sec-slot0:;dir /all sec-disk0:;dir /all sec-slot1:;dir /all sec-disk1:;dir /all sec-slot2:;dir /all sec-disk2:;show controllers;show controllers cbus;show diagbus;admin show diag;show diag;show module;show spe version;show c7200;show inventory raw;show vtp status;show vlan;show vlan-switch;show debug;more system:running-config;show running-config;write term" <switchname>
<switchname> clogin error: Error: TIMEOUT reached
<switchname> clogin error: Error: TIMEOUT reached
<switchname>: missed cmd(s): admin show diag,dir /all slavedisk2:,show rsp chassis-info,dir /all sec-slot2:,show diag,dir /all disk1:,show gsr chassis,dir /all sec-nvram:,show diag chassis-info,dir /all disk2:,dir /all sec-bootflash:,show spe version,dir /all slaveslot2:,dir /all disk0:,show install active,show bootvar,dir /all slaveslot0:,dir /all sec-slot1:,dir /all harddiska:,dir /all slavenvram:,show flash,dir /all sec-disk2:,dir /all slavesup-bootflash:,dir /all sec-disk0:,dir /all harddiskb:,show variables boot,show boot,show inventory raw,dir /all slavedisk1:,show env all,show module,admin show env all,show controllers,admin show version,show diagbus,more system:running-config,dir /all slavedisk0:,show debug,show idprom backplane,dir /all bootflash:,dir /all sec-slot0:,dir /all sec-disk1:,write term,show vtp status,dir /all sup-bootflash:,dir /all slot2:,dir /all harddisk:,dir /all slot0:,dir /all sup-microcode:,show vlan,dir /all slavebootflash:,show controllers cbus,dir /all slaveslot1:,dir /all nvram:,show version,show vlan-switch,admin show variables boot,show redundancy secondary,show running-config,show c7200,dir /all slot1:
<switchname>: missed cmd(s): admin show diag,dir /all slavedisk2:,show rsp chassis-info,dir /all sec-slot2:,show diag,dir /all disk1:,show gsr chassis,dir /all sec-nvram:,show diag chassis-info,dir /all disk2:,dir /all sec-bootflash:,show spe version,dir /all slaveslot2:,dir /all disk0:,show install active,show bootvar,dir /all slaveslot0:,dir /all sec-slot1:,dir /all harddiska:,dir /all slavenvram:,show flash,dir /all sec-disk2:,dir /all slavesup-bootflash:,dir /all sec-disk0:,dir /all harddiskb:,show variables boot,show boot,show inventory raw,dir /all slavedisk1:,show env all,show module,admin show env all,show controllers,admin show version,show diagbus,more system:running-config,dir /all slavedisk0:,show debug,show idprom backplane,dir /all bootflash:,dir /all sec-slot0:,dir /all sec-disk1:,write term,show vtp status,dir /all sup-bootflash:,dir /all slot2:,dir /all harddisk:,dir /all slot0:,dir /all sup-microcode:,show vlan,dir /all slavebootflash:,show controllers cbus,dir /all slaveslot1:,dir /all nvram:,show version,show vlan-switch,admin show variables boot,show redundancy secondary,show running-config,show c7200,dir /all slot1:
<switchname>: End of run not found
<switchname>: End of run not found
!
[rancid at pwsecLX bin]$


-----Original Message-----
From: Lance Vermilion [mailto:rancid at gheek.net]
Sent: Thursday, February 26, 2009 11:30 AM
To: Mina Eskander; rancid-discuss at shrubbery.net
Subject: Re: [rancid] Re: How do i downgrade from 2.3.2a9 to 2.3.2a8

When you login do you start off at the (enable) prompt? If so do you
have autoenable 1 in your .cloginrc for that host?

On Thu, Feb 26, 2009 at 9:21 AM, Mina Eskander
<meskander at perimeterwatch.com> wrote:
> The 6509 is running in hybrid mode, the switching modules are running catos 6.4(11) and the routing modules are polling just fine.
>
> switch> (enable) sh ver
> WS-C6509 Software, Version NmpSW: 6.4(11)
>
>
> -----Original Message-----
> From: rancid-discuss-bounces at shrubbery.net [mailto:rancid-discuss-bounces at shrubbery.net] On Behalf Of Lance Vermilion
> Sent: Thursday, February 26, 2009 10:55 AM
> To: rancid-discuss at shrubbery.net
> Subject: [rancid] Re: How do i downgrade from 2.3.2a9 to 2.3.2a8
>
> 6509's typically run IOS now not CATOS. Paste back to us the version
> of your software that you are running on the 6509s.
>
> On Wed, Feb 25, 2009 at 12:09 PM, Mina Eskander
> <meskander at perimeterwatch.com> wrote:
>> I am having problems contacting my catos switches, I have 2 6509's
>>
>> I have the type in my router.db as cat5, and clogin works fine, but when I
>> run rancid or cat5rancid it just hangs after getting into enable mode.
>>
>> I have autoenable set to 0 so it has to enter the enable password.
>>
>>
>>
>> I read in another post that somebody downgraded to 2.3.2a8 and it works, but
>> I need some help downgrading.
>>
>> I am running
>>
>> Linux version 2.6.23.12-52.fc7 (mockbuild at xenbuilder4.fedora.phx.redhat.com)
>> (gcc version 4.1.2 20070925 (Red Hat 4.1.2-27))
>>
>>
>>
>> Please help
>>
>>
>>
>>
>>
>> _______________________________________________
>> Rancid-discuss mailing list
>> Rancid-discuss at shrubbery.net
>> http://www.shrubbery.net/mailman/listinfo.cgi/rancid-discuss
>>
> _______________________________________________
> Rancid-discuss mailing list
> Rancid-discuss at shrubbery.net
> http://www.shrubbery.net/mailman/listinfo.cgi/rancid-discuss
>