[rancid] Re: How do i downgrade from 2.3.2a9 to 2.3.2a8

Thu Feb 26 17:03:26 UTC 2009

[rancid at pwsecLX bin]$ clogin -c "show time" <switchname>
<switchname>
spawn telnet <switchname>
Trying <ipadd>...
Connected to <switchname>.
Escape character is '^]'.

Cisco Systems Console

WARNING!!!
This system is solely for the use of authorized users for official purposes.
You have no expectation of privacy in its use and to ensure that the system
is functioning properly, individuals using this computer system are subject
to having all of their activities monitored and recorded by system
personnel. Use of this system evidences an express consent to such
monitoring and agreement that if such monitoring reveals evidence of
possible abuse or criminal activity, system personnel may provide the results
of such monitoring to appropriate officials.

Username: <username>

Password:
switch> enable

Enter password:
switch> (enable)
switch> (enable) set length 0
Screen length for this session set to 0.
switch> (enable)
Error: TIMEOUT reached
[rancid at pwsecLX bin]$

Mina Eskander
Perimeterwatch Technologies
Direct:   +1 (347) 448-2845
Mobile:   +1 (347) 510-4102
meskander at perimeterwatch.com

Network Security | Disaster Recovery | Business Continuity | IT Projects | Application Development
_____________________________________________________________________
New York: (347) 448-2845 - 34-12 36th Street - 2nd Floor - Astoria, NY 11106

-----Original Message-----
From: Lance Vermilion [mailto:rancid at gheek.net]
Sent: Thursday, February 26, 2009 11:55 AM
To: Mina Eskander
Cc: rancid-discuss at shrubbery.net
Subject: Re: [rancid] Re: How do i downgrade from 2.3.2a9 to 2.3.2a8

You might want to source the conf file in "<rancid
home>/etc/rancid.conf" to make sure you have all the same environment
variables when you use clogin by default.

It is timing out for a reason and I am not 100% sure why. I would
think because it can't recognize the prompt correctly, or maybe you
have some characters like "#" in your login/banner motd that it is
seeing.

paste back to the list

 clogin -c "show time" <host>

On Thu, Feb 26, 2009 at 9:38 AM, Mina Eskander
<meskander at perimeterwatch.com> wrote:
> I have autoenable set to 0, so rancid has to manually enter the enable password, when I do a clogin <switchname> it logs in and gets into enable mode just fine.
> But when I run rancid -d <switchname> I get the following output
>
> [rancid at pwsecLX bin]$ rancid -d <switchname>
> executing clogin -t 90 -c"admin show version;show version;show redundancy secondary;show idprom backplane;show install active;admin show env all;show env all;show rsp chassis-info;show gsr chassis;show diag chassis-info;show boot;show bootvar;admin show variables boot;show variables boot;show flash;dir /all nvram:;dir /all bootflash:;dir /all slot0:;dir /all disk0:;dir /all slot1:;dir /all disk1:;dir /all slot2:;dir /all disk2:;dir /all harddisk:;dir /all harddiska:;dir /all harddiskb:;dir /all sup-bootflash:;dir /all sup-microcode:;dir /all slavenvram:;dir /all slavebootflash:;dir /all slaveslot0:;dir /all slavedisk0:;dir /all slaveslot1:;dir /all slavedisk1:;dir /all slaveslot2:;dir /all slavedisk2:;dir /all slavesup-bootflash:;dir /all sec-nvram:;dir /all sec-bootflash:;dir /all sec-slot0:;dir /all sec-disk0:;dir /all sec-slot1:;dir /all sec-disk1:;dir /all sec-slot2:;dir /all sec-disk2:;show controllers;show controllers cbus;show diagbus;admin show diag;show diag;show module;show spe version;show c7200;show inventory raw;show vtp status;show vlan;show vlan-switch;show debug;more system:running-config;show running-config;write term" <switchname>
> <switchname> clogin error: Error: TIMEOUT reached
> <switchname> clogin error: Error: TIMEOUT reached
> <switchname>: missed cmd(s): admin show diag,dir /all slavedisk2:,show rsp chassis-info,dir /all sec-slot2:,show diag,dir /all disk1:,show gsr chassis,dir /all sec-nvram:,show diag chassis-info,dir /all disk2:,dir /all sec-bootflash:,show spe version,dir /all slaveslot2:,dir /all disk0:,show install active,show bootvar,dir /all slaveslot0:,dir /all sec-slot1:,dir /all harddiska:,dir /all slavenvram:,show flash,dir /all sec-disk2:,dir /all slavesup-bootflash:,dir /all sec-disk0:,dir /all harddiskb:,show variables boot,show boot,show inventory raw,dir /all slavedisk1:,show env all,show module,admin show env all,show controllers,admin show version,show diagbus,more system:running-config,dir /all slavedisk0:,show debug,show idprom backplane,dir /all bootflash:,dir /all sec-slot0:,dir /all sec-disk1:,write term,show vtp status,dir /all sup-bootflash:,dir /all slot2:,dir /all harddisk:,dir /all slot0:,dir /all sup-microcode:,show vlan,dir /all slavebootflash:,show controllers cbus,dir /all slaveslot1:,dir /all nvram:,show version,show vlan-switch,admin show variables boot,show redundancy secondary,show running-config,show c7200,dir /all slot1:
> <switchname>: missed cmd(s): admin show diag,dir /all slavedisk2:,show rsp chassis-info,dir /all sec-slot2:,show diag,dir /all disk1:,show gsr chassis,dir /all sec-nvram:,show diag chassis-info,dir /all disk2:,dir /all sec-bootflash:,show spe version,dir /all slaveslot2:,dir /all disk0:,show install active,show bootvar,dir /all slaveslot0:,dir /all sec-slot1:,dir /all harddiska:,dir /all slavenvram:,show flash,dir /all sec-disk2:,dir /all slavesup-bootflash:,dir /all sec-disk0:,dir /all harddiskb:,show variables boot,show boot,show inventory raw,dir /all slavedisk1:,show env all,show module,admin show env all,show controllers,admin show version,show diagbus,more system:running-config,dir /all slavedisk0:,show debug,show idprom backplane,dir /all bootflash:,dir /all sec-slot0:,dir /all sec-disk1:,write term,show vtp status,dir /all sup-bootflash:,dir /all slot2:,dir /all harddisk:,dir /all slot0:,dir /all sup-microcode:,show vlan,dir /all slavebootflash:,show controllers cbus,dir /all slaveslot1:,dir /all nvram:,show version,show vlan-switch,admin show variables boot,show redundancy secondary,show running-config,show c7200,dir /all slot1:
> <switchname>: End of run not found
> <switchname>: End of run not found
> !
> [rancid at pwsecLX bin]$
>
>
> -----Original Message-----
> From: Lance Vermilion [mailto:rancid at gheek.net]
> Sent: Thursday, February 26, 2009 11:30 AM
> To: Mina Eskander; rancid-discuss at shrubbery.net
> Subject: Re: [rancid] Re: How do i downgrade from 2.3.2a9 to 2.3.2a8
>
> When you login do you start off at the (enable) prompt? If so do you
> have autoenable 1 in your .cloginrc for that host?
>
> On Thu, Feb 26, 2009 at 9:21 AM, Mina Eskander
> <meskander at perimeterwatch.com> wrote:
>> The 6509 is running in hybrid mode, the switching modules are running catos 6.4(11) and the routing modules are polling just fine.
>>
>> switch> (enable) sh ver
>> WS-C6509 Software, Version NmpSW: 6.4(11)
>>
>>
>> -----Original Message-----
>> From: rancid-discuss-bounces at shrubbery.net [mailto:rancid-discuss-bounces at shrubbery.net] On Behalf Of Lance Vermilion
>> Sent: Thursday, February 26, 2009 10:55 AM
>> To: rancid-discuss at shrubbery.net
>> Subject: [rancid] Re: How do i downgrade from 2.3.2a9 to 2.3.2a8
>>
>> 6509's typically run IOS now not CATOS. Paste back to us the version
>> of your software that you are running on the 6509s.
>>
>> On Wed, Feb 25, 2009 at 12:09 PM, Mina Eskander
>> <meskander at perimeterwatch.com> wrote:
>>> I am having problems contacting my catos switches, I have 2 6509's
>>>
>>> I have the type in my router.db as cat5, and clogin works fine, but when I
>>> run rancid or cat5rancid it just hangs after getting into enable mode.
>>>
>>> I have autoenable set to 0 so it has to enter the enable password.
>>>
>>>
>>>
>>> I read in another post that somebody downgraded to 2.3.2a8 and it works, but
>>> I need some help downgrading.
>>>
>>> I am running
>>>
>>> Linux version 2.6.23.12-52.fc7 (mockbuild at xenbuilder4.fedora.phx.redhat.com)
>>> (gcc version 4.1.2 20070925 (Red Hat 4.1.2-27))
>>>
>>>
>>>
>>> Please help
>>>
>>>
>>>
>>>
>>>
>>> _______________________________________________
>>> Rancid-discuss mailing list
>>> Rancid-discuss at shrubbery.net
>>> http://www.shrubbery.net/mailman/listinfo.cgi/rancid-discuss
>>>
>> _______________________________________________
>> Rancid-discuss mailing list
>> Rancid-discuss at shrubbery.net
>> http://www.shrubbery.net/mailman/listinfo.cgi/rancid-discuss
>>
>