[rancid] HP ProCurve MSM410 AccessPoint

[shouldbe q931]

On Fri, Jan 13, 2012 at 10:02 AM, Helmut Wieser <helmut.wieser at ieee.org> wrote:
> Hi,
>
> I've got rancid running fine with a variety of devices. However I've got a
> few HP ProCurve MSM410 access points that I would like to monitor with
> rancid as well. I can log in fine with hlogin. But they do not support "show
> system" or "show system information". Instead the command needs to be "show
> system info".
>
> Is anyone using those devices in rancid? I tried type "hp" in router.db, but
> this doesn't work.
>
> Here's sample "show system info" output:
>
> CLI# show system info
>                                                [CPU info]               [Mem
> info]
> Firmware Version: 5.3.1.0-y-xxxx          Load 1min:       0.00   Total RAM:
>  263438336
> Uptime:           123 days, 03:56>         Load 5min:       0.00    Free
> RAM:  219406336
> Board Revision:   50-00-1036-02            Load 15min:      0.00  Buffer
> RAM:    6041600
> Serial Number:    xxxxxxxxxx               CPU use now:       0%   Cache
> RAM:   14221312
>                                           CPU 5sec ago:      1%
> [Storage use]
>                                           CPU 10sec ago:     0%   Permanent:
>        3%
>                                           CPU 20sec ago:     1%   Temporary:
>        1%
>
>
> This is a list of all commands:
>
> end:
>        Switches to parent context.
> reboot device:
>        Restarts the system.
> show interfaces:
>        Show networking interfaces.
> show bridge:
>        Show bridge information.
> show bridge forwarding:
>        Show bridge forwarding information.
> show arp:
>        Show the ARP table.
> show ip:
>        Show all IP addresses.
> show ip route:
>        Show all IP routes.
> show dns cache [<serial>]:
>        Show DNS cache entries. Specify a serial number to display detailed
> information.
> show system info:
>        Show basic system information.
> show certificate:
>        Display current certificates.
> show certificate binding:
>        Display how the certificates are used.
> sh:
>        Protected access to shell.
> arp <arguments>:
>        Displays and modifies the Internet-to-Ethernet address translation
> tables used by the address resolution protocol.
> iperf <arguments>:
>        Runs a performance throughput test.
> ping <arguments>:
>        Determines if  the specified remote IP address is active.
> arping <arguments>:
>        Pings a destination on a device interface using ARP packets.
> quit:
>        Exit the enable context.
> rcapture <arguments>:
>        Sends port capture to an FTP server.
> dumpstats <arguments>:
>        Display internal status.
> show all config:
>        Print all configuration that applies to this device.
> show client log [<macaddr>]:
>        Display client station log. Enter the MAC address to display more
> details for a specific client station.
> show wireless neighborhood:
>        Show all access points detected nearby.
> show wireless rogue-ap:
>        Show all rogue access points detected nearby.
> show dot11 associations:
>        Show all current wireless associations.
> show dot11 statistics client-traffic:
>        Show current client matrix statistics.
> show local mesh:
>        Show current local mesh  interfaces.
> config:
>        Switches to the config context.
> factory reset:
>        Resets the unit to factory default settings.
> switch operational mode:
>        Switches the unit operational mode.
>
>
> kind regards,
> Helmut Wieser
> _______________________________________________
> Rancid-discuss mailing list
> Rancid-discuss at shrubbery.net
> http://www.shrubbery.net/mailman/listinfo.cgi/rancid-discuss

Which version of rancid are you using, and are you using it for any
other HP devices ?