[rancid] Release Authorised RANCID Email Issue
heasley
heas at shrubbery.net
Thu Apr 11 14:47:53 UTC 2013
Thu, Apr 11, 2013 at 10:38:33AM -0400, Gilmour, Scott:
> Hi,
> When I run bin/clogin 192.168.150.1 I can log into my Enterasys Switch.
> Since I am using an Enterasys Switch I should be using rivlogin since this
> is what rancid-run will use for my vendor.
> But when I run rivlogin I get:
> $ bin/rivlogin 192.168.150.1
> 192.168.150.1
> ERROR: no enable password found for 192.168.150.1 in
> /usr/local/rancid/.cloginrc.
> $
>
> My Understanding if I do add autoenable 192.168.150.1 1 then the 1 would
> tell the script not to use the enable password. Or is there something in
> the script I need to change?
> When I finally run the rancid-run I will edited the rivlogin script to do
> just a show config or show config all.
>
> # Rancid .cloginrc setup
> add user 192.168.150.1 tacacssu
> add password 192.168.150.1 tacacs
> add autoenable 192.168.150.1 1
> add method 192.168.150.1 ssh
that script was written by guys from enterasys; it does not support autoenable
like the other scripts. looking at the code, i suspect that if you just
change the line to
add password 192.168.150.1 {tacacs} {}
it will work.
> Thanks
> Scott
>
> On Fri, Apr 5, 2013 at 12:00 PM, Marito ... <me_gogorza at hotmail.com> wrote:
>
> > Scott,
> >
> > Please check in your router.db which vendor you setup. As per your log
> > file , the script is trying to execute "system show XXXX", while the rancid
> > script executes "show XXXX".
> >
> > I think you are using the rivrancid/rivlogin scripts for this
> > devices. Instead of using clogin, try rivlogin -c 'system show XXXX'
> > 192.168.150.1 (where XXXX is your comand)
> >
> > Regards.
> > Mario
> >
> > ------------------------------
> > Date: Fri, 5 Apr 2013 10:28:11 -0400
> > From: sgilmour at enterasys.com
> > To: rwest at zyedge.com
> > CC: rancid-discuss at shrubbery.net
> > Subject: Re: [rancid] Release Authorised RANCID Email Issue
> >
> > Ryan,
> > Here is the output:
> >
> > $ bin/rancid -d 192.168.150.1
> > executing clogin -t 90 -c"show version;show redundancy secondary;show
> > idprom backplane;show install active;show env all;show rsp
> > chassis-info;show gsr chassis;show diag chassis-info;show boot;show
> > bootvar;show variables boot;show flash;dir /all nvram:;dir /all
> > bootflash:;dir /all slot0:;dir /all disk0:;dir /all slot1:;dir /all
> > disk1:;dir /all slot2:;dir /all disk2:;dir /all harddisk:;dir /all
> > harddiska:;dir /all harddiskb:;dir /all sup-bootdisk:;dir /all
> > sup-bootflash:;dir /all sup-microcode:;dir /all slavenvram:;dir /all
> > slavebootflash:;dir /all slaveslot0:;dir /all slavedisk0:;dir /all
> > slaveslot1:;dir /all slavedisk1:;dir /all slaveslot2:;dir /all
> > slavedisk2:;dir /all slavesup-bootflash:;dir /all sec-nvram:;dir /all
> > sec-bootflash:;dir /all sec-slot0:;dir /all sec-disk0:;dir /all
> > sec-slot1:;dir /all sec-disk1:;dir /all sec-slot2:;dir /all sec-disk2:;show
> > controllers;show config;show controllers cbus;show diagbus;show diag;show
> > capture;show module;show spe version;show c7200;show inventory raw;show vtp
> > status;show vlan;show vlan-switch;show debug;show shun;more
> > system:running-config;show running-config view full;show
> > running-config;show config;write term" 192.168.150.1
> > sh: 1: clogin: not found
> > 192.168.150.1: missed cmd(s): dir /all slavedisk2:,show rsp
> > chassis-info,show capture,dir /all sec-slot2:,show diag,dir /all
> > disk1:,show gsr chassis,dir /all sec-nvram:,show diag chassis-info,dir /all
> > disk2:,show running-config view full,dir /all sec-bootflash:,show spe
> > version,dir /all slaveslot2:,dir /all disk0:,show install active,show
> > bootvar,dir /all slaveslot0:,dir /all sec-slot1:,dir /all harddiska:,dir
> > /all slavenvram:,show flash,dir /all sec-disk2:,dir /all
> > slavesup-bootflash:,dir /all sec-disk0:,dir /all harddiskb:,show variables
> > boot,show boot,show inventory raw,dir /all slavedisk1:,show env all,show
> > module,show shun,show controllers,show diagbus,more
> > system:running-config,dir /all slavedisk0:,show debug,show idprom
> > backplane,dir /all bootflash:,dir /all sup-bootdisk:,dir /all
> > sec-slot0:,show config,dir /all sec-disk1:,write term,show vtp status,dir
> > /all sup-bootflash:,dir /all slot2:,dir /all harddisk:,dir /all slot0:,dir
> > /all sup-microcode:,show vlan,dir /all slavebootflash:,show controllers
> > cbus,dir /all slaveslot1:,dir /all nvram:,show version,show
> > vlan-switch,show redundancy secondary,show running-config,show c7200,dir
> > /all slot1:
> > 192.168.150.1: missed cmd(s): dir /all slavedisk2:,show rsp
> > chassis-info,show capture,dir /all sec-slot2:,show diag,dir /all
> > disk1:,show gsr chassis,dir /all sec-nvram:,show diag chassis-info,dir /all
> > disk2:,show running-config view full,dir /all sec-bootflash:,show spe
> > version,dir /all slaveslot2:,dir /all disk0:,show install active,show
> > bootvar,dir /all slaveslot0:,dir /all sec-slot1:,dir /all harddiska:,dir
> > /all slavenvram:,show flash,dir /all sec-disk2:,dir /all
> > slavesup-bootflash:,dir /all sec-disk0:,dir /all harddiskb:,show variables
> > boot,show boot,show inventory raw,dir /all slavedisk1:,show env all,show
> > module,show shun,show controllers,show diagbus,more
> > system:running-config,dir /all slavedisk0:,show debug,show idprom
> > backplane,dir /all bootflash:,dir /all sup-bootdisk:,dir /all
> > sec-slot0:,show config,dir /all sec-disk1:,write term,show vtp status,dir
> > /all sup-bootflash:,dir /all slot2:,dir /all harddisk:,dir /all slot0:,dir
> > /all sup-microcode:,show vlan,dir /all slavebootflash:,show controllers
> > cbus,dir /all slaveslot1:,dir /all nvram:,show version,show
> > vlan-switch,show redundancy secondary,show running-config,show c7200,dir
> > /all slot1:
> > 192.168.150.1: End of run not found
> > 192.168.150.1: End of run not found
> > !
> > you have mail
> > $
> >
> >
> > Starting rancid-run
> > bin/rancid-run
> > /usr/local/rancid/var/logs/networking.20130405.102327
> >
> > starting: Fri Apr 5 10:23:27 EDT 2013
> >
> >
> >
> > Trying to get all of the configs.
> > 192.168.200.1: missed cmd(s): system show hardware,system show
> > version,system show active-config,system show uptime
> > 192.168.200.1: End of run not found
> > 192.168.150.1: missed cmd(s): system show hardware,system show
> > version,system show active-config,system show uptime
> > 192.168.150.1: End of run not found
> > 192.168.200.4: missed cmd(s): system show hardware,system show
> > version,system show active-config,system show uptime
> > 192.168.200.4: End of run not found
> > !
> > !
> > !
> > =====================================
> > Getting missed routers: round 1.
> > 192.168.200.4: missed cmd(s): system show hardware,system show
> > version,system show active-config,system show uptime
> > 192.168.200.4: End of run not found
> > 192.168.200.1: missed cmd(s): system show hardware,system show
> > version,system show active-config,system show uptime
> > 192.168.200.1: End of run not found
> > !
> > 192.168.150.1: missed cmd(s): system show hardware,system show
> > version,system show active-config,system show uptime
> > 192.168.150.1: End of run not found
> > !
> > !
> > =====================================
> > Getting missed routers: round 2.
> > 192.168.150.1: missed cmd(s): system show hardware,system show
> > version,system show active-config,system show uptime
> > 192.168.150.1: End of run not found
> > 192.168.200.1: missed cmd(s): system show hardware,system show
> > version,system show active-config,system show uptime
> > 192.168.200.1: End of run not found
> > 192.168.200.4: missed cmd(s): system show hardware,system show
> > version,system show active-config,system show uptime
> > 192.168.200.4: End of run not found
> > !
> > !
> > !
> > =====================================
> > Getting missed routers: round 3.
> > 192.168.150.1: missed cmd(s): system show hardware,system show
> > version,system show active-config,system show uptime
> > 192.168.150.1: End of run not found
> > 192.168.200.1: missed cmd(s): system show hardware,system show
> > version,system show active-config,system show uptime
> > 192.168.200.1: End of run not found
> > 192.168.200.4: missed cmd(s): system show hardware,system show
> > version,system show active-config,system show uptime
> > 192.168.200.4: End of run not found
> > !
> > !
> > !
> > =====================================
> > Getting missed routers: round 4.
> > 192.168.200.1: missed cmd(s): system show hardware,system show
> > version,system show active-config,system show uptime
> > 192.168.200.1: End of run not found
> > 192.168.200.4: missed cmd(s): system show hardware,system show
> > version,system show active-config,system show uptime
> > 192.168.200.4: End of run not found
> > !
> > 192.168.150.1: missed cmd(s): system show hardware,system show
> > version,system show active-config,system show uptime
> > 192.168.150.1: End of run not found
> > !
> > !
> >
> > cvs diff: Diffing .
> > cvs diff: Diffing configs
> > cvs commit: Examining .
> > cvs commit: Examining configs
> >
> > ending: Fri Apr 5 10:23:28 EDT 2013
> >
> >
> >
> > On Fri, Apr 5, 2013 at 9:37 AM, Ryan West <rwest at zyedge.com> wrote:
> >
> > On Fri, Apr 05, 2013 at 08:14:19, Gilmour, Scott wrote:
> > > Subject: Re: [rancid] Release Authorised RANCID Email Issue
> > >
> > > Yes I can do for example bin/clogin -c 'show config' 192.168.150.1
> > > and that logs in without any issue.
> > > If I do a bin/rancid-run that is where my issue is occurring. I am
> > > debugging the script to see if there is something I need to edit in the
> > script.
> > >
> > Try rancid -d 192.168.150.1 and post that. What's in your logs when you
> > try rancid-run?
> >
> >
> >
> >
> > --
> >
> > Scott Gilmour | SQA Engineer
> >
> > Enterasys Networks | A Siemens Enterprise Communications Company
> >
> > Office: (603) 952-5924
> >
> > Email: sgilmour at enterasys.com
> >
> > _______________________________________________ Rancid-discuss mailing
> > list Rancid-discuss at shrubbery.net
> > http://www.shrubbery.net/mailman/listinfo.cgi/rancid-discuss
> >
>
>
>
> --
>
> Scott Gilmour | SQA Engineer
>
> Enterasys Networks | A Siemens Enterprise Communications Company
>
> Office: (603) 952-5924
>
> Email: sgilmour at enterasys.com
> _______________________________________________
> Rancid-discuss mailing list
> Rancid-discuss at shrubbery.net
> http://www.shrubbery.net/mailman/listinfo.cgi/rancid-discuss
More information about the Rancid-discuss
mailing list