[rancid] Release Authorised RANCID Email Issue
Gilmour, Scott
sgilmour at enterasys.com
Thu Apr 11 15:35:22 UTC 2013
Thanks Heasley,
Now it is just Timing out when getting to the Username Prompt
Username:
Username:ERROR: Timeout on login Exiting
On Thu, Apr 11, 2013 at 10:47 AM, heasley <heas at shrubbery.net> wrote:
> Thu, Apr 11, 2013 at 10:38:33AM -0400, Gilmour, Scott:
> > Hi,
> > When I run bin/clogin 192.168.150.1 I can log into my Enterasys Switch.
> > Since I am using an Enterasys Switch I should be using rivlogin since
> this
> > is what rancid-run will use for my vendor.
> > But when I run rivlogin I get:
> > $ bin/rivlogin 192.168.150.1
> > 192.168.150.1
> > ERROR: no enable password found for 192.168.150.1 in
> > /usr/local/rancid/.cloginrc.
> > $
> >
> > My Understanding if I do add autoenable 192.168.150.1 1 then the 1 would
> > tell the script not to use the enable password. Or is there something in
> > the script I need to change?
> > When I finally run the rancid-run I will edited the rivlogin script to
> do
> > just a show config or show config all.
> >
> > # Rancid .cloginrc setup
> > add user 192.168.150.1 tacacssu
> > add password 192.168.150.1 tacacs
> > add autoenable 192.168.150.1 1
> > add method 192.168.150.1 ssh
>
> that script was written by guys from enterasys; it does not support
> autoenable
> like the other scripts. looking at the code, i suspect that if you just
> change the line to
>
> add password 192.168.150.1 {tacacs} {}
>
> it will work.
>
> > Thanks
> > Scott
> >
> > On Fri, Apr 5, 2013 at 12:00 PM, Marito ... <me_gogorza at hotmail.com>
> wrote:
> >
> > > Scott,
> > >
> > > Please check in your router.db which vendor you setup. As per your log
> > > file , the script is trying to execute "system show XXXX", while the
> rancid
> > > script executes "show XXXX".
> > >
> > > I think you are using the rivrancid/rivlogin scripts for this
> > > devices. Instead of using clogin, try rivlogin -c 'system show XXXX'
> > > 192.168.150.1 (where XXXX is your comand)
> > >
> > > Regards.
> > > Mario
> > >
> > > ------------------------------
> > > Date: Fri, 5 Apr 2013 10:28:11 -0400
> > > From: sgilmour at enterasys.com
> > > To: rwest at zyedge.com
> > > CC: rancid-discuss at shrubbery.net
> > > Subject: Re: [rancid] Release Authorised RANCID Email Issue
> > >
> > > Ryan,
> > > Here is the output:
> > >
> > > $ bin/rancid -d 192.168.150.1
> > > executing clogin -t 90 -c"show version;show redundancy secondary;show
> > > idprom backplane;show install active;show env all;show rsp
> > > chassis-info;show gsr chassis;show diag chassis-info;show boot;show
> > > bootvar;show variables boot;show flash;dir /all nvram:;dir /all
> > > bootflash:;dir /all slot0:;dir /all disk0:;dir /all slot1:;dir /all
> > > disk1:;dir /all slot2:;dir /all disk2:;dir /all harddisk:;dir /all
> > > harddiska:;dir /all harddiskb:;dir /all sup-bootdisk:;dir /all
> > > sup-bootflash:;dir /all sup-microcode:;dir /all slavenvram:;dir /all
> > > slavebootflash:;dir /all slaveslot0:;dir /all slavedisk0:;dir /all
> > > slaveslot1:;dir /all slavedisk1:;dir /all slaveslot2:;dir /all
> > > slavedisk2:;dir /all slavesup-bootflash:;dir /all sec-nvram:;dir /all
> > > sec-bootflash:;dir /all sec-slot0:;dir /all sec-disk0:;dir /all
> > > sec-slot1:;dir /all sec-disk1:;dir /all sec-slot2:;dir /all
> sec-disk2:;show
> > > controllers;show config;show controllers cbus;show diagbus;show
> diag;show
> > > capture;show module;show spe version;show c7200;show inventory
> raw;show vtp
> > > status;show vlan;show vlan-switch;show debug;show shun;more
> > > system:running-config;show running-config view full;show
> > > running-config;show config;write term" 192.168.150.1
> > > sh: 1: clogin: not found
> > > 192.168.150.1: missed cmd(s): dir /all slavedisk2:,show rsp
> > > chassis-info,show capture,dir /all sec-slot2:,show diag,dir /all
> > > disk1:,show gsr chassis,dir /all sec-nvram:,show diag chassis-info,dir
> /all
> > > disk2:,show running-config view full,dir /all sec-bootflash:,show spe
> > > version,dir /all slaveslot2:,dir /all disk0:,show install active,show
> > > bootvar,dir /all slaveslot0:,dir /all sec-slot1:,dir /all
> harddiska:,dir
> > > /all slavenvram:,show flash,dir /all sec-disk2:,dir /all
> > > slavesup-bootflash:,dir /all sec-disk0:,dir /all harddiskb:,show
> variables
> > > boot,show boot,show inventory raw,dir /all slavedisk1:,show env
> all,show
> > > module,show shun,show controllers,show diagbus,more
> > > system:running-config,dir /all slavedisk0:,show debug,show idprom
> > > backplane,dir /all bootflash:,dir /all sup-bootdisk:,dir /all
> > > sec-slot0:,show config,dir /all sec-disk1:,write term,show vtp
> status,dir
> > > /all sup-bootflash:,dir /all slot2:,dir /all harddisk:,dir /all
> slot0:,dir
> > > /all sup-microcode:,show vlan,dir /all slavebootflash:,show controllers
> > > cbus,dir /all slaveslot1:,dir /all nvram:,show version,show
> > > vlan-switch,show redundancy secondary,show running-config,show
> c7200,dir
> > > /all slot1:
> > > 192.168.150.1: missed cmd(s): dir /all slavedisk2:,show rsp
> > > chassis-info,show capture,dir /all sec-slot2:,show diag,dir /all
> > > disk1:,show gsr chassis,dir /all sec-nvram:,show diag chassis-info,dir
> /all
> > > disk2:,show running-config view full,dir /all sec-bootflash:,show spe
> > > version,dir /all slaveslot2:,dir /all disk0:,show install active,show
> > > bootvar,dir /all slaveslot0:,dir /all sec-slot1:,dir /all
> harddiska:,dir
> > > /all slavenvram:,show flash,dir /all sec-disk2:,dir /all
> > > slavesup-bootflash:,dir /all sec-disk0:,dir /all harddiskb:,show
> variables
> > > boot,show boot,show inventory raw,dir /all slavedisk1:,show env
> all,show
> > > module,show shun,show controllers,show diagbus,more
> > > system:running-config,dir /all slavedisk0:,show debug,show idprom
> > > backplane,dir /all bootflash:,dir /all sup-bootdisk:,dir /all
> > > sec-slot0:,show config,dir /all sec-disk1:,write term,show vtp
> status,dir
> > > /all sup-bootflash:,dir /all slot2:,dir /all harddisk:,dir /all
> slot0:,dir
> > > /all sup-microcode:,show vlan,dir /all slavebootflash:,show controllers
> > > cbus,dir /all slaveslot1:,dir /all nvram:,show version,show
> > > vlan-switch,show redundancy secondary,show running-config,show
> c7200,dir
> > > /all slot1:
> > > 192.168.150.1: End of run not found
> > > 192.168.150.1: End of run not found
> > > !
> > > you have mail
> > > $
> > >
> > >
> > > Starting rancid-run
> > > bin/rancid-run
> > > /usr/local/rancid/var/logs/networking.20130405.102327
> > >
> > > starting: Fri Apr 5 10:23:27 EDT 2013
> > >
> > >
> > >
> > > Trying to get all of the configs.
> > > 192.168.200.1: missed cmd(s): system show hardware,system show
> > > version,system show active-config,system show uptime
> > > 192.168.200.1: End of run not found
> > > 192.168.150.1: missed cmd(s): system show hardware,system show
> > > version,system show active-config,system show uptime
> > > 192.168.150.1: End of run not found
> > > 192.168.200.4: missed cmd(s): system show hardware,system show
> > > version,system show active-config,system show uptime
> > > 192.168.200.4: End of run not found
> > > !
> > > !
> > > !
> > > =====================================
> > > Getting missed routers: round 1.
> > > 192.168.200.4: missed cmd(s): system show hardware,system show
> > > version,system show active-config,system show uptime
> > > 192.168.200.4: End of run not found
> > > 192.168.200.1: missed cmd(s): system show hardware,system show
> > > version,system show active-config,system show uptime
> > > 192.168.200.1: End of run not found
> > > !
> > > 192.168.150.1: missed cmd(s): system show hardware,system show
> > > version,system show active-config,system show uptime
> > > 192.168.150.1: End of run not found
> > > !
> > > !
> > > =====================================
> > > Getting missed routers: round 2.
> > > 192.168.150.1: missed cmd(s): system show hardware,system show
> > > version,system show active-config,system show uptime
> > > 192.168.150.1: End of run not found
> > > 192.168.200.1: missed cmd(s): system show hardware,system show
> > > version,system show active-config,system show uptime
> > > 192.168.200.1: End of run not found
> > > 192.168.200.4: missed cmd(s): system show hardware,system show
> > > version,system show active-config,system show uptime
> > > 192.168.200.4: End of run not found
> > > !
> > > !
> > > !
> > > =====================================
> > > Getting missed routers: round 3.
> > > 192.168.150.1: missed cmd(s): system show hardware,system show
> > > version,system show active-config,system show uptime
> > > 192.168.150.1: End of run not found
> > > 192.168.200.1: missed cmd(s): system show hardware,system show
> > > version,system show active-config,system show uptime
> > > 192.168.200.1: End of run not found
> > > 192.168.200.4: missed cmd(s): system show hardware,system show
> > > version,system show active-config,system show uptime
> > > 192.168.200.4: End of run not found
> > > !
> > > !
> > > !
> > > =====================================
> > > Getting missed routers: round 4.
> > > 192.168.200.1: missed cmd(s): system show hardware,system show
> > > version,system show active-config,system show uptime
> > > 192.168.200.1: End of run not found
> > > 192.168.200.4: missed cmd(s): system show hardware,system show
> > > version,system show active-config,system show uptime
> > > 192.168.200.4: End of run not found
> > > !
> > > 192.168.150.1: missed cmd(s): system show hardware,system show
> > > version,system show active-config,system show uptime
> > > 192.168.150.1: End of run not found
> > > !
> > > !
> > >
> > > cvs diff: Diffing .
> > > cvs diff: Diffing configs
> > > cvs commit: Examining .
> > > cvs commit: Examining configs
> > >
> > > ending: Fri Apr 5 10:23:28 EDT 2013
> > >
> > >
> > >
> > > On Fri, Apr 5, 2013 at 9:37 AM, Ryan West <rwest at zyedge.com> wrote:
> > >
> > > On Fri, Apr 05, 2013 at 08:14:19, Gilmour, Scott wrote:
> > > > Subject: Re: [rancid] Release Authorised RANCID Email Issue
> > > >
> > > > Yes I can do for example bin/clogin -c 'show config' 192.168.150.1
> > > > and that logs in without any issue.
> > > > If I do a bin/rancid-run that is where my issue is occurring. I am
> > > > debugging the script to see if there is something I need to edit in
> the
> > > script.
> > > >
> > > Try rancid -d 192.168.150.1 and post that. What's in your logs when
> you
> > > try rancid-run?
> > >
> > >
> > >
> > >
> > > --
> > >
> > > Scott Gilmour | SQA Engineer
> > >
> > > Enterasys Networks | A Siemens Enterprise Communications Company
> > >
> > > Office: (603) 952-5924
> > >
> > > Email: sgilmour at enterasys.com
> > >
> > > _______________________________________________ Rancid-discuss mailing
> > > list Rancid-discuss at shrubbery.net
> > > http://www.shrubbery.net/mailman/listinfo.cgi/rancid-discuss
> > >
> >
> >
> >
> > --
> >
> > Scott Gilmour | SQA Engineer
> >
> > Enterasys Networks | A Siemens Enterprise Communications Company
> >
> > Office: (603) 952-5924
> >
> > Email: sgilmour at enterasys.com
>
> > _______________________________________________
> > Rancid-discuss mailing list
> > Rancid-discuss at shrubbery.net
> > http://www.shrubbery.net/mailman/listinfo.cgi/rancid-discuss
>
>
--
Scott Gilmour | SQA Engineer
Enterasys Networks | A Siemens Enterprise Communications Company
Office: (603) 952-5924
Email: sgilmour at enterasys.com
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://www.shrubbery.net/pipermail/rancid-discuss/attachments/20130411/0b61844e/attachment.html>
More information about the Rancid-discuss
mailing list