| Component |
Remove
|
Replace
|
Tips |
| System Cover |
5.6
|
9.1
|
|
| Power Supply |
6.1
|
6.1.2
|
|
Cable Assemblies
Diskette drive cable
Diskette drive power cable
Primary IDE Cable
Secondary IDE Cable
Smart card reader cable
Power switch/LED |
6.2.1
6.2.3
6.2.5
6.2.7
6.2.9
6.2.11
|
6.2.2
6.2.4
6.2.6
6.2.8
6.2.10
6.2.12
|
- Cannot be ordered separately.
Cable Service Kit covers all system cable assemblies.
|
| Speaker Assembly |
6.3.1
|
6.3.2
|
|
| Fan Assembly |
6.4.1
|
6.4.2
|
|
| Diskette Drive |
7.1.1
|
7.1.2
|
|
| Smart Card Reader II (SCR) |
7.2.1
|
7.2.2
|
- Solaris 8 02/02 also requires these SCR II patches:
 109887 Smart card core fixes and 110457 Internal card reader fixes. SMC II requires the
installation of Java Development Kit (JDK) V1.2.2 build 11.
-
Page 3 of the
Sun Blade 150 Product Notes (816-1163) describes operational status of SCR LED.
-
Green, non flashing LED indicates smart card (media) is correctly inserted.
Green, flashing LED indicates data read/write to or from smart card (media).
Amber, non flashing LED indicates smart card (media) not inserted correctly.
|
| Primary Hard Drive |
7.3.1
|
7.3.2
|
|
| Secondary Hard Drive |
|
7.3.3
|
- Optional secondary drives include the secondary IDE cable.
- Before installing a secondary drive, be sure to jumper for "Cable
Select".
- Find IDE Cabling Configuration information in Appendix A.5.1.
|
| CD-ROM or DVD-ROM Drive |
7.4.1
|
7.4.2
|
- Appendix A.5.2 describes CD-ROM and DVD-ROM jumper settings.
|
| CPU |
8.1.1
|
8.2.2
|
- Note from Appendix C.5.1: Power on banner, POST and the OpenBoot PROM report the CPU as an UltraSPARC-IIe[tm] processor. The SunBlade 150 CPU is an UltraSPARC-IIi.
|
| NVRAM/TOD |
8.2.1
|
8.2.2
|
|
| DIMMs |
8.3.1
|
8.3.2
|
- Early Sun Blade 150 systems were manufactured with incorrectly labeled
DIMMs (FIN I0901-1).
- Either 1, 2 or 4 DIMMs must be installed. Always fill connectors [1],
or [1 and 2], or [1,2,3 and 4]. Never fill connectors [1, 2 and 3] without
filling connector [4].
- To identify a failed DIMM, see TABLE 4-2 in section 4.5 of the Service
Manual.
- Memory Architecture information is found in Appendix C.9.
- Also reference the SunBlade 150
DIMM Installation Guide (816-5370).
|
| PCI card |
8.4.1
|
8.4.2
|
-
Maximum power consumption for all three PCI connectors is 50 watts.
- Do not install a combination of PCI cards and/or graphics accelerators that
have a combined power consumption of 50 watts or more.
|
| Motherboard |
8.5.1
|
8.5.2
|
|
| Riser Board |
8.6.1
|
8.6.2
|
|
