|
System Administration Commands | pgxconfig(1M) |
| pgxconfig, GFXconfig - configure the PGX32 (Raptor GFX) Graphics Accelerator |
SYNOPSIS
| /usr/sbin/pgxconfig [-dev device-filename] [-res video-mode [ try | noconfirm | nocheck]] [-file machine | system ] [-depth 8 | 24 ] [-24only true | false] [-cachedpixmap true | false] [-defaults] |
| /usr/sbin/pgxconfig [-propt] [-prconf] |
| /usr/sbin/pgxconfig [-help] [-res ?] |
|
The pgxconfig utility configures the PGX32 (Raptor GFX) Graphics Accelerator and some of the X11 window system defaults for PGX32 (Raptor GFX). A previous version of this utility was named GFXconfig.
The first form of pgxconfig shown in the synopsis above stores the specified options in the OWconfig file. These options are used to initialize the PGX32 (Raptor GFX) device the next time the window system is run on that device. Updating options in the OWconfig file provides persistence
of these options across window system sessions and system reboots.
The second, third, and fourth forms, which invoke only the -prconf, -propt, -help, and -res ? options, do not update the OWconfig file. For the third form all other options are ignored.
The -i option starts pgxconfig in interactive mode.
Options may be specified for only one PGX32 (Raptor GFX) device at a time.
Only PGX32 (Raptor GFX)-specific options can be specified through pgxconfig. The normal window system options for specifying default depth, default visual class and so forth are still specified as device modifiers on the openwin command line. See the Xsun(1) manual page available with the SUNWxwman package.
The user can also specify the OWconfig file that is to be updated. By default, the machine-specific file in the /usr/openwin directory tree is updated. The -file option can be used to specify an alternate file to use. For example, the system-global OWconfig file
in the /etc/openwin directory tree can be updated instead.
Both of these standard OWconfig files can only be written by root.
|
|
The following options are supported:
- -cachedpixmap true | false
- When set to false, it forces the PGX32 (Raptor GFX) device to use 24-bit only when running OpenWindows. The default value is true.
Certain applications make use of a cached pixmap when writing to the display device. Such a technique can cause garbled output and can cause the X server to crash. If you experience such behavior, try setting the -cachedpixmap option to false.
- -defaults
- Reset all option values to their default values.
- -depth 8 | 24
- Sets the screen depth to 8 or 24 bits per pixel. 24 bits per pixel enables TrueColor graphics in the window system.
- -dev device-filename
- Specify the PGX32 (Raptor GFX) special file. The default is /dev/fbs/gfxp0, or /dev/fbs/raptor0 if applicable.
- -file machine | system
- Specify which OWconfig file to update. If machine, the machine-specific OWconfig file in the /etc/openwin directory tree is used. If system, the global OWconfig file in the /usr/openwin directory tree is used. If the file does not exist, it is created.
- -help
- Print a list of the pgxconfig command line options, along with a brief explanation of each.
- -i
- Start pgxconfig in interactive mode.
- -prconf
- Print the PGX32 (Raptor GFX) hardware configuration. Thie following is a typical display:
|
--- Hardware Configuration for /dev/fbs/gfxp0 ---
DAC: version 0x0
Type:
Board:
PROM: version 0x0
PROM Information:
RAM:
EDID Data:
Monitor Sense ID:
Card possible resolutions: 640x480x60, 800x600x75, 1024x768x60
1024x768x70, 1024x768x75, 1280x1024x75, 1280x1024x76
1280x1024x60, 1152x900x66, 1152x900x76, 1280x1024x67
960x680x112S, 960x680x108S, 640x480x60i, 768x575x50i,
1280x800x76, 1440x900x76, 1600x1000x66, 1600x1000x76,
vga, svga, 1152, 1280, stereo, ntsc, pal
Monitor possible resolutions: 720x400x70, 720x400x88, 640x480x60
640x480x67, 640x480x72, 640x480x75, 800x600x56,
800x600x60, 800x600x72, 800x600x75, 832x624x75,
1024x768x87, 1024x768x60, 1024x768x70, 1024x768x75,
1280x1024x75, 1280x1024x76, 1152x900x66, 1152x900x76,
1280x1024x67, 960x680x112S, vga, svga, 1152, 1280
stereo
Current resolution setting: 1280x1024x76
Possible depths: 8, 24, 8+24
Current depth: 8
|
- -propt
- Print the current values of all PGX32 (Raptor GFX) options in the OWconfig file specified by the -file option for the device specified by the -dev option. Print the values of options
as they would be in the OWconfig file after the call to pgxconfig would have completed. The following is a typical display:
|
--- OpenWindows Configuration for /dev/fbs/gfxp0 ---
OWconfig: machine
Video Mode: not set
Depth: 8+24
|
- -res video-mode [try | noconfirm | nocheck ]
- Specify the built-in video mode used to drive the monitor connected to the specified PGX32 (Raptor GFX) device.
The format for video-mode can be one of the following:
-
widthxheightxrate
- The width is the screen width in pixels, height is the screen height
in pixels, and rate is the vertical frequency of the screen refresh. As a convenience, -res also accepts formats with @ prepended to the refresh rate rather than x. For example: 1280x1024@76. The list can be obtained by running pgxconfig with the -res ? option (the third form shown in the command synopsis above). Note that not all resolutions are supported by both the video board and by the monitor. The pgxconfig utility will not permit you to set a resolution not supported
by the board unless the noconfirm or nocheck option is specified. It will also request confirmation before setting a resolution not supported by the monitor if the nocheck option is not specified.
- Symbolic names
- For convenience, the video modes listed below have symbolic names defined. Rather than the form widthxheightxrate, the symbolic
name may be supplied as the argument to -res. If the symbolic name is none, the screen resolution will be the video mode that is currently programmed in the device when the window system is run.
-
svga
- 1024x768x60
-
1152
- 1152x900x76
-
1280
- 1280x1024x76
-
vga
- 640x480x60
-
none
- default console resolution
The -res option also accepts additional, optional arguments immediately following the video mode specification. Any or all of these may be present.
-
noconfirm
- Using the -res option, the user could put the system into an unusable state, a state where there is no video output. This can happen if there is ambiguity in the monitor sense codes for the particular code read. To
reduce the chance of this occurring, the default behavior of pgxconfig is to print a warning message to this effect and to prompt the user to find out if it is okay to continue. The noconfirm option instructs pgxconfig to bypass this confirmation
and to program the requested video mode anyway. This option is useful when pgxconfig is being run from a shell script.
-
nocheck
- If present, normal error checking based on the monitor sense code is suspended. The video mode specified by the user will be accepted regardless of whether it is appropriate for the currently attached monitor. (This option is useful
if a different monitor is to be connected to the PGX32 (Raptor GFX) device). Use of this option implies noconfirm as well.
-
try
- This option allows the user to test the specified resolution before committing it. It displays a pattern on the screen with the specified resolution. If the test pattern appears correctly, the user may answer "y" to the query. The other
permissable answer is "n".
- -res ?
- Print the list of possible resolutions supported by the PGX32 and the monitor.
- -24only
- Force the PGX32 (Raptor GFX) device to use 24 bit only when running Openwindows.
|
|
For a given invocation of pgxconfig, if an option does not appear on the command line, the corresponding OWconfig option is not updated; it retains its previous value, except for -depth and -24only.
A default value is used if a PGX32 (Raptor GFX) option has not been specified with pgxconfig when the window system is run. The option defaults are as follows:
- -dev
-
/dev/fbs/gfxp0
- -file
-
system
- -res
- none
The default of none for the -res option indicates that when the window system is run, the screen resolution will be the video mode that is currently programmed in the device.
|
| Example 1. Switching the Resolution on the Monitor Type
|
The following example switches the monitor type to the resolution of 1280 x 1024 at 76 Hz:
|
example# /usr/sbin/pgxconfig -res 1280x1024x76
|
|
|
|
-
/dev/fbs/gfxp0
- device special file
-
/usr/openwin/server/etc/OWconfig
- system configuration file
-
/etc/openwin/server/etc/OWconfig
- machine configuration file
|
|
PGX32 Installation Manual
|
| |