Sun Microsystems, Inc.
spacerspacer
spacer   www.sun.com docs.sun.com | | |  
spacer
black dot
   
A   B   C   D   E   F   G   H   I   J   K   L   M   N   O   P   Q   R   S   T   U   V   W   X   Y   Z
    
 
Process Control Library Functionsps_pstop(3PROC)


NAME

 ps_pstop, ps_pcontinue, ps_lstop, ps_lcontinue, ps_lrolltoaddr, ps_kill - process and LWP control in libthread_db

SYNOPSIS

 
#include <proc_service.h> 
ps_err_e ps_pstop(struct ps_prochandle *ph);
 ps_err_e ps_pcontinue(struct ps_prochandle *ph);
 ps_err_e ps_lstop(struct ps_prochandle *ph, lwpid_t lwpid);
 ps_err_e ps_lcontinue(struct ps_prochandle *ph, lwpid_t lwpid);
 ps_err_e ps_lrolltoaddr(struct ps_prochandle *ph, lwpid_t lwpid, psaddr_t go_addr, psaddr_t stop_addr);
 ps_err_e ps_kill(struct ps_prochandle *ph, int signum);

DESCRIPTION

 

The ps_pstop() function stops the target process identified by ph, while the ps_pcontinue() function allows it to resume.

The libthread_db() function uses ps_pstop() to freeze the target process while it is under inspection. Within the scope of any single call from outside libthread_db to a libthread_db routine, libthread_db will call ps_pstop(), at most once. If it does, it will call ps_pcontinue() within the scope of the same routine.

The controlling process may already have stopped the target process when it calls libthread_db. In that case, it is not obligated to resume the target process when libthread_db calls ps_pcontinue(). In other words, ps_pstop() is mandatory, while ps_pcontinue() is advisory. After ps_pstop(), the target process must be stopped; after ps_pcontinue(), the target process may be running.

The ps_lstop() and ps_lcontinue() functions stop and resume a single lightweight process (LWP) within the target process ph.

The ps_lrolltoaddr() function is used to roll an LWP forward out of a critical section when the process is stopped. It is also used to run the libthread_db agent thread on behalf of libthread. The ps_lrolltoaddr() function is always called with the target process stopped, that is, there has been a preceding call to ps_pstop(). The specified LWP must be continued at the address go_addr, or at its current address if go_addr is NULL. It should then be stopped when its execution reaches stop_addr. This routine does not return until the LWP has stopped at stop_addr.

The ps_kill() function directs the signal signum to the target process for which the handle is ph. It has the same semantics as kill(2).

RETURN VALUES

 
PS_OK
The call completed successfully. In the case of ps_pstop(), the target process is stopped.
PS_BADLID
For ps_lstop(), ps_lcontinue() and ps_lrolltoaddr(); there is no LWP with id lwipd in the target process.
PS_ERR
The function did not return successfully.

ATTRIBUTES

 

See attributes(5) for description of the following attributes:

ATTRIBUTE TYPEATTRIBUTE VALUE
MT LevelSafe

SEE ALSO

 

kill(2), libthread(3LIB), libthread_db(3LIB), libthread_db(3THR), proc_service(3PROC), threads(3THR), attributes(5)


SunOS 5.9Go To TopLast Changed 22 Mar 2001

 
      
      
Copyright 2002 Sun Microsystems, Inc. All rights reserved. Use is subject to license terms.